- 您现在的位置：买卖IC网 > PDF目录379309 > MC33219AP (MOTOROLA INC) VOICE SWITCHED SPEAKERPHONE CIRCUIT PDF资料下载
参数资料
| 型号： | MC33219AP |
| 厂商： | MOTOROLA INC |
| 元件分类： | 无绳电话/电话 |
| 英文描述： | VOICE SWITCHED SPEAKERPHONE CIRCUIT |
| 中文描述： | SPEAKER PHONE CIRCUIT, PDIP24 |
| 封装： | 0.300 INCH, PLASTIC, DIP-24 |
| 文件页数： | 23/28页 |
| 文件大小： | 562K |
| 代理商： | MC33219AP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页
MC33219A
23
MOTOROLA ANALOG IC DEVICE DATA
of speech” to the attenuator control block. Grounding CPT
does the same for the transmit path.
Additionally, the receive background noise monitor is
automatically disabled by the dial tone detector whenever the
receive signal exceeds the detector’s threshold.
Dial Tone Detector Threshold
The threshold for the dial tone detector is internally set at
≈
20 mV (14 mVrms) below VB (see Figure 29). That
threshold can be adjusted if desired by changing the bias at
RAI. The method used depends on how the input of the
receive attenuator is connected to other circuitry.
a) If the attenuator input (RAI) is DC coupled to the receive
amplifier (Pins 15 to 16 as in Figure 2), or to some other
amplifier in the system, then the threshold is changed by
forcing a small offset on that amplifier. As shown in Figure 32,
connect a resistor (RTO) from the summing node to either
ground or VCC, depending on whether the dial tone detector
threshold is to be increased or decreased. RF and RI are the
resistors normally used to set the gain of that amplifier.
Figure 32. Adjusting Dial Tone Detector
Threshold (DC Coupled)
RI
Audio
Signal
Input
100 k
RXO
RTO
VCC or
GND
VB
VB
RXI
RF
RAI
20 mV
VB
Attenuator
To
Attentuator
Control
Circuit
Adding RTO and connecting it to ground will shift RXO and
RAI upward, thereby increasing the dial tone detector
threshold. In this case, RTO is calculated from:
RTO
VB
RF
V
VB is the voltage at Pin 6, and
V is the amount that the
detector’s threshold is increased. For example, if VB = 2.2 V,
and RF = 10 k, and the threshold is to be increased by 20 mV,
RTO calculates to 1.1 M
.
Connecting RTO to VCC will shift RXO downward, thereby
decreasing the dial tone detector threshold. In this case, RTO
is calculated from:
RTO
(VCC– VB)
RF
V
For example, if VCC = 5.0 V, VB = 2.2 V, and RF = 10 k and
the threshold is to be decreased by 10 mV, RTO calculates to
2.8 M
.
b) If the receive attenuator input is AC coupled to the
receive amplifier or to other circuitry, then the offset is set at
RAI. The circuits in Figure 33 are suggested for changing
the threshold.
Figure 33. Adjusting Dial Tone Detector
Threshold (AC Coupled)
Audio
Signal
Input
VCC
3.0 k
56 k
RTO
RAI
VB
To Increase The Threshold
To Decrease The Threshold
100 k
VB
20 mV
VB
Attenuator
To
Control
Circuit
DTD
Audio
Signal
Input
RTO
RAI
100 k
VB
20 mV
VB
Attenuator
To
Control
Circuit
DTD
56 k
3.0 k
VB
To increase the threshold, use the first circuit in Figure 33.
The voltage at the top of the 3.0 k resistor is between 90 and
180 mV above VB (depending on VCC). RTO and the 100 k
input impedance form a voltage divider to create the desired
offset at RAI. RTO is calculated from:
RTO
((VCC– VB)
0.05)
V
– 1
(100 k)
For example, if VCC = 5.0 V, and the threshold is to be
increased by 20 mV (
V), RTO calculates to
≈
600 k
.
If the threshold is to be decreased, use the second circuit
in Figure 33. RTO is calculated from:
RTO
(VB
0.05)
V
– 1
(100 k)
RFI Interference
Potential radio frequency interference (RFI) problems
should be addressed early in the electrical and mechanical
design of the speakerphone. RFI may enter the circuit
through Tip and Ring, through the microphone wiring to the
microphone amplifier (which should be short), or through any
of the PC board traces. The most sensitive pins on the
MC33219A are the inputs to the level detectors (RLI, TLI,
XDI) since, when there is no speech present, the inputs are
high impedance and these op amps are in a near open–loop
condition. The board traces to these pins should be kept
相关PDF资料 |
PDF描述 |
|---|---|
| MC33290D | ISO SERIAL LINK INTERFACE |
| MC33290 | ISO SERIAL LINK INTERFACE |
| MC33290DR2 | ISO SERIAL LINK INTERFACE |
| MC33290P | ISO SERIAL LINK INTERFACE |
| MC33304D | RAIL-TO-RAIL SLEEPMODE OPERATIONAL AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33232D | 功能描述:功率因数校正 IC Critical Mode PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| MC33232DG | 功能描述:功率因数校正 IC Critical Mode PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| MC33232DR2 | 功能描述:功率因数校正 IC Critical Mode PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| MC33232DR2G | 功能描述:功率因数校正 IC Critical Mode PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
| MC33232P | 功能描述:功率因数校正 IC Critical Mode PFC RoHS:否 制造商:Fairchild Semiconductor 开关频率:300 KHz 最大功率耗散: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。