参数资料
型号: MC33288
厂商: 飞思卡尔半导体(中国)有限公司
英文描述: Solid State Relay for Automotive Flasher Applications(固态继电器,适用于自动闪光器)
中文描述: 固态继电器(固态继电器,适用于自动闪光器闪光器的汽车应用)
文件页数: 2/8页
文件大小: 382K
代理商: MC33288
MC33288
PINS FUNCTION DESCRIPTION
Solid State Relay for Automotive Flasher Applications
Go to: www.freescale.com
2
Pin No.
Name/Function
Description
TAB
V
bat
Supply Voltage
The backside TAB is connected to the power supply of the
MC33288DH. In addition to its supply function, this pin contributes to
the thermal behaviour of the device by conducting the heat from the
switching MOSFET to the printed circuit board.
6,7,8
13,14,15
OUT1
OUTPUT Channel 1
OUT 2
OUTPUT Channel 2
Pins 6,7,8 are the source of the output1 25mOhm MOSFET1. Pins
13,14,15 are source of the output 2 25mOhm MOSFET2. They deliver
current to the connected loads and are respectively controlled via the
IN1 and IN2 pins. These outputs are current limited and thermally
protected.
3
18
IN 1
INPUT Channel 1
IN 2
INPUT Channel 2
These are the device input pins which directly control their associated
outputs. The levels are CMOS compatible. When the input is a logic
low, the associated output MOSFET is in the off state. When input is
high, the MOSFET is turned on and the load is activated.
When both inputs are low, the device is in standby mode and its
supply current is reduced. Each input pin has an internal active pull
down, so that it will not float if disconnected.
19
Status
Status for both
Channels
The Fault output is an open drain indication that goes active low when
a fault mode (Openload, Overtemp) is detected by the device on
either one channel or both simultaneously. Its internal structure is an
open drain architecture with an internal clamp at 6V. An external pull
up resistor connected to Vdd (5V) is needed. See Functional Truth
Table.
20
Wlp
Warning Lamp Output
This pin is the source of a 3.2 Ohm MOSFET. This output is current
limited and thermally protected. It delivers current through the
connected load when both IN1 and IN2 inputs are logic high. It is usually
used as a warning lamp driver for Flasher application.
2
Cur R
Load Current Sense
The Current Sense pin deliver a ratioed amount (1/1000) of the sum
of the currents that can be used to generate signal ground referenced
output voltages for use by the microcontroller.
4, 9, 10, 11, 12, 17
NC
Not Connected
These pins are not used.
5, 16
DNC
Do Not Connect
These pins must not be connected.
11
GND
GROUND
This is the Ground pin of the device.
Freescale Semiconductor, Inc.
相关PDF资料
PDF描述
MC33289 Dual High-Side Switch(双高端开关)
MC33290 ISO K Line Serial Link Interface(串行ISO K-Line接口)
MC33291L Eight Output Switch with Serial Peripheral Interface I/O(带SPI接口的八输出开关)
MC33291 Eight Output Switch with Serial Peripheral Interface I/O(带SPI接口的八输出开关)
MC33298 Eight Output Switch with Serial Peripheral Interface I/O(带SPI接口的八输出开关)
相关代理商/技术参数
参数描述
MC33288ADH 制造商:Freescale Semiconductor 功能描述:POWER SWITCH HI SIDE 40A 22-PIN (20+2TAB) HSOP - Rail/Tube
MC33288ADHR2 制造商:Freescale Semiconductor 功能描述:POWER SWITCH HI SIDE 40A 22-PIN (20+2TAB) HSOP T/R - Tape and Reel
MC33288DDH 功能描述:电源开关 IC - 配电 FLASHER RoHS:否 制造商:Exar 输出端数量:1 开启电阻(最大值):85 mOhms 开启时间(最大值):400 us 关闭时间(最大值):20 us 工作电源电压:3.2 V to 6.5 V 电源电流(最大值): 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5
MC33288DDHR2 功能描述:电源开关 IC - 配电 FLASHER RoHS:否 制造商:Exar 输出端数量:1 开启电阻(最大值):85 mOhms 开启时间(最大值):400 us 关闭时间(最大值):20 us 工作电源电压:3.2 V to 6.5 V 电源电流(最大值): 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5
MC33289 制造商:SPC Multicomp 功能描述:HEATSINK TO220 10.2/W 3 HOLES 制造商:SPC Multicomp 功能描述:HEATSINK TO220 10.2C/W 3 HOLES 制造商:SPC Multicomp 功能描述:HEAT SINK; Packages Cooled:TO-220; Thermal Resistance:10.2C/W; External Height - Imperial:1.496"; External Height - Metric:38mm; External Width - Imperial:1.358"; External Width - Metric:34.5mm; External Length - Imperial:0.492" ;RoHS Compliant: Yes