- 您现在的位置：买卖IC网 > PDF目录18700 > MC33690DWE (Freescale Semiconductor)IC STAND ALONE TAG READER 20SOIC PDF资料下载
参数资料
| 型号： | MC33690DWE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 10/26页 |
| 文件大小： | 0K |
| 描述： | IC STAND ALONE TAG READER 20SOIC |
| 标准包装： | 38 |
| RF 型： | 读/写 |
| 频率： | 125kHz |
| 特点： | 电源电压范围广 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 管件 |
Standalone Configuration with One-Wire Bus
Table 4. Communication Modes Description
Configuration
Configuration Pins
Pin Status Function Description
Type
Bus Type
Name
Mode1
Mode2
Standalone
1 wire (VBAT)
A
0
0
K output/input:
? demodulator output
? amplitude modulation input
? shutdown/wake-up
AM must be connected to VSUP
DOUT forces a low level
2 wires (VBAT)
B
0
1
K output:
? demodulator output
AM input:
? amplitude modulation input
? shutdown/wake-up
DOUT forces a low level
Direct
2 wires (VDD)
C
1
x
DOUT output:
Connection to
a MCU
1
0
? demodulator output
AM input:
? amplitude modulation input
MODE2 input:
? shutdown/wake-up
K output/input (standalone ISO 9141 interface):
? driven by Tx and monitored by Rx
K input (standalone ISO 9141 interface):
? monitored by Rx
? Tx disabled
7
Standalone Configuration with One-Wire Bus
When a low level is applied on pins MODE1 and MODE2, the circuit is in configuration A (see Figure 24 ). After power on, the
circuit is set into read mode. The demodulator output is directly routed to the ISO 9141 interface output K.
The circuit can be set into write mode at anytime by violation of all possible patterns on the single wire bus during more than
1ms. Then, the K line achieves the amplitude modulation by switching on/off both antenna drivers.
After 1ms of inactivity at the end of the challenge phase (bus in idle recessive one state), the circuit is set back into read mode.
The circuit can be put into standby mode by forcing the K line at zero during more than 2 ms after entering the write mode.
After the K line is released, the circuit sends an acknowledge pulse before entering into standby mode. In standby mode, the
oscillator and most of the internal biasing currents are switched off. Therefore, the functions (tag reader, ISO 9141 driver) are
inactive except the voltage regulator and the ISO 9141 receiver on pin K. The driver output TD1 forces a low level and TD2
forces a high level. A rising edge on K wakes up the circuit. After completion of the wake-up sequence, the circuit is
automatically set in read mode.
In configuration A, DOUT and Rx outputs always force a low level and Tx is disabled.
MC33690 Standalone Tag Reader Circuit, Rev. 5
10
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| XPGWHT-P1-0000-008E7 | XLAMP XP-G LED WARM/NEUTRAL WHT |
| XPGWHT-P1-0000-007F8 | XLAMP XP-G LED WARM/NEUTRAL WHT |
| 264S4S1 | CABLE R/A 4POS FEMALE-FEMALE 1M |
| XPGWHT-P1-0000-007E8 | XLAMP XP-G LED WARM/NEUTRAL WHT |
| XPGWHT-L1-0000-00BF7 | LED XLAMP 3200K WARM WHITE SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33690DWER2 | 功能描述:数字信号处理器和控制器 - DSP, DSC STAND ALONE TAG READER RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MC33696FCAE | 功能描述:射频收发器 UHF TRANSCEIVER RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCAER2 | 功能描述:射频收发器 UHF TRANSCEIVER ECHO RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCE | 功能描述:射频收发器 PLL Tuned UHF Recvr RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCER2 | 功能描述:射频收发器 PLL Tuned UHF Recvr RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。