- 您现在的位置：买卖IC网 > PDF目录18700 > MC33690DWE (Freescale Semiconductor)IC STAND ALONE TAG READER 20SOIC PDF资料下载
参数资料
| 型号： | MC33690DWE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 13/26页 |
| 文件大小： | 0K |
| 描述： | IC STAND ALONE TAG READER 20SOIC |
| 标准包装： | 38 |
| RF 型： | 读/写 |
| 频率： | 125kHz |
| 特点： | 电源电压范围广 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 管件 |
Direct Connection to a Microcontroller Configuration
9
Direct Connection to a Microcontroller Configuration
When a high level is applied on MODE1, the circuit is in configuration C (see Figure 26 ). The demodulated data are sent
through DOUT.
The AM pin is set as a VDD referenced input pin receiving the AM command. Forcing high and low levels on AM achieves the
amplitude modulation by switching on/off both antenna drivers. Meanwhile, this amplitude modulation can be monitored on
DOUT. This allows antenna short and open circuit diagnosis.
The circuit can be put into standby mode by applying a low level on the MODE2 pin. In standby mode, the oscillator and most
of the internal biasing currents are switched off. Therefore, the functions (tag reader and ISO 9141 interface) are inactive except
for the voltage regulator. The driver outputs TD1 and TD2 are frozen in their state (high or low level) before entering into
standby mode. DOUT forces a low level.
The ISO 9141 interface K is standalone and can be directly controlled by the input pin Tx and monitored by the output Rx.
Applying a logic high level on Tx switches the output driver K on (dominant zero state when an external pull-up resistor is
connected between K and VBAT). Applying a logic low level turns the driver off (one recessive state).
Rx monitors the voltage at the K pin. When the voltage is below the low threshold voltage, Rx forces a logic low level. When
the voltage is above the high threshold voltage, Rx forces a logic high level.
In standby mode, Tx is disabled and Rx output monitors the voltage at the K pin.
Reset
TD1/2
switching
AM low
AM high
AM high
TD1/2 off
Wake-up
AM low
mode2 low
mode2 low
mode2 high
Standby
Figure 10. Configuration C State Diagram
10
Electrical Characteristics
Typical values reflect average measurements at V SUP = 12V and T J = 25 ° C.
11
Supply Current
Typical values reflect average measurements at 6V ≤ V SUP ≤ 16V, V SS = 0V, T J = –40 ° C to + 125 ° C, unless otherwise noted.
MC33690 Standalone Tag Reader Circuit, Rev. 5
Freescale Semiconductor
13
相关PDF资料 |
PDF描述 |
|---|---|
| XPGWHT-P1-0000-008E7 | XLAMP XP-G LED WARM/NEUTRAL WHT |
| XPGWHT-P1-0000-007F8 | XLAMP XP-G LED WARM/NEUTRAL WHT |
| 264S4S1 | CABLE R/A 4POS FEMALE-FEMALE 1M |
| XPGWHT-P1-0000-007E8 | XLAMP XP-G LED WARM/NEUTRAL WHT |
| XPGWHT-L1-0000-00BF7 | LED XLAMP 3200K WARM WHITE SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33690DWER2 | 功能描述:数字信号处理器和控制器 - DSP, DSC STAND ALONE TAG READER RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MC33696FCAE | 功能描述:射频收发器 UHF TRANSCEIVER RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCAER2 | 功能描述:射频收发器 UHF TRANSCEIVER ECHO RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCE | 功能描述:射频收发器 PLL Tuned UHF Recvr RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCER2 | 功能描述:射频收发器 PLL Tuned UHF Recvr RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。