- 您现在的位置：买卖IC网 > Datasheet目录475 > MC33690DWER2 (Freescale Semiconductor)IC STAND ALONE TAG READER 20SOIC Datasheet资料下载
参数资料
| 型号： | MC33690DWER2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 12/26页 |
| 文件大小： | 0K |
| 描述： | IC STAND ALONE TAG READER 20SOIC |
| 标准包装： | 1,000 |
| RF 型： | 读/写 |
| 频率： | 125kHz |
| 特点： | 电源电压范围广 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 带卷 (TR) |
Standalone Configuration with Two-Wire Bus
8
Standalone Configuration with Two-Wire Bus
When a low level is applied on MODE1 and a high level on MODE2, the circuit is in configuration B (see Figure 25 ). The K
pin is set as an output sending the demodulated data.
The AM pin is set as a VSUP referenced input pin receiving the amplitude modulation and the shutdown/wake-up commands.
Forcing high and low levels on AM achieves the amplitude modulation by switching on/off both antenna drivers. This amplitude
modulation can be monitored on the K output and allows antenna short and open circuit diagnosis. The circuit can be put into
standby mode by forcing the AM line at zero during more than 2 ms. The circuit sends an acknowledge pulse before entering
into standby mode.
In standby mode, the oscillator and most of the internal biasing currents are switched off. Therefore, the functions (tag reader
and ISO 9141 driver) are inactive except for the voltage regulator and the ISO 9141 receiver on pin AM. The driver output TD1
forces a low level and TD2 a high level. A rising edge on AM wakes up the circuit. After completion of the wake-up sequence,
the circuit is automatically set in read mode.
In configuration B, DOUT and Rx outputs always force a low level and Tx is disabled.
Read and write sequences:
drivers on
drivers off
data write modulation
AM line
1
1
1
0
0
0
data read
data write
K line
1
1
1
0
0
0
Entering into standby mode:
AM line monitoring
AM line
t ? T1
acknowledge
standby mode
K line
T1
T2
T2
Coming out of standby mode:
AM line
standby mode
wake-up sequence
data read
K line
Figure 8. Modes Access Description in Two-wire Bus Configuration
Reset
TD1/2
switching
AM line low
AM line high
AM line high
TD1/2 off
Wake-up
AM line low
T1 ￡ AM line low
AM
Standby
Figure 9. Configuration B State Diagram
MC33690 Standalone Tag Reader Circuit, Rev. 5
12
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MC44CC375AVEFEVK | CCEVK NEJA EVAL KIT |
| MCH3374-TL-E | MOSFET P-CH 12V 3A MCPH3 |
| MCH3375-TL-H | MOSFET P-CH 1.6A 30V MCPH3 |
| MCH3377-TL-E | MOSFET P-CH 20V 3A MCPH3 |
| MCH3377-TL-H | MOSFET P-CH 3A 20V MCPH3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33696FCAE | 功能描述:射频收发器 UHF TRANSCEIVER RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCAER2 | 功能描述:射频收发器 UHF TRANSCEIVER ECHO RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCE | 功能描述:射频收发器 PLL Tuned UHF Recvr RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FCER2 | 功能描述:射频收发器 PLL Tuned UHF Recvr RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MC33696FJAE | 功能描述:射频收发器 UHF REICEVER RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。