- 您现在的位置：买卖IC网 > PDF目录359133 > MC33742 (飞思卡尔半导体(中国)有限公司) System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver(带增强型高速CAN收发器的系统基片) PDF资料下载
参数资料
| 型号： | MC33742 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 元件分类： | CAN |
| 英文描述： | System Basis Chip (SBC) with Enhanced High-Speed CAN Transceiver(带增强型高速CAN收发器的系统基片) |
| 中文描述： | 系统基础芯片的增强型（SBC）的高速CAN收发器（带增强型高速的CAN收发器的系统基片） |
| 文件页数： | 18/52页 |
| 文件大小： | 1087K |
| 代理商： | MC33742 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
33742
18
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
SYSTEM/APPLICATION INFORMATION
INTRODUCTION
The 33742 and the 33742S are integrated circuits dedicated
to automotive applications. Their functions include the
following:
One fully protected voltage regulator with 200 mA total
output current capability available at the V
DD
terminal.
Driver for external pass transistor for V2 regulator
function.
V
DD
regulator undervoltage reset function, programmable
window or timeout software watchdog function.
Two running modes: Normal and Standby modes when
the microcontroller is running.
Sleep and Stop modes for operation in low power mode to
reduce the application current consumption, while offering
wake-up capability from CAN interface, L3:L0 wake-up
input, and automatic timer wake-up.
Programmable wake-up input and cyclic sense wake-up.
CAN high-speed physical interface with bus failure
diagnostic and enhanced protection feature for TXD and
RXD failure.
Interface with micro through SPI. Interrupt output to report
device status, diagnostic, and wake-up event.
FUNCTIONAL TERMINAL DESCRIPTION
RXD and TXD
The RXD and TXD terminals (receive data terminal and
transmit data terminal, respectively) are connected to the
microcontroller CAN protocol handler. TXD is an input and
controls the CANH and CANL line state (dominant when TXD is
LOW, recessive when TXD is HIGH). RXD is an output and
reports the bus state (RXD LOW when CAN bus is dominant,
HIGH when CAN bus is recessive).
V
DD
The V
DD
terminal is the output terminal of the 5.0 V internal
regulator. It can deliver up to 200 mA. This output is protected
against overcurrent and overtemperature. It includes an
overtemperature pre-warning flag, which is set when the
internal regulator temperature exceeds 130°C typical. When
the temperature exceeds the overtemperature shutdown
(170°C typical), the regulator is turned off.
V
DD
includes an undervoltage reset circuitry, which sets the
RST
terminal LOW when V
DD
is below the undervoltage reset
threshold.
RST
The Reset terminal
RST
is an output that is set LOW when
the device is in reset mode. The
RST
terminal is set HIGH when
the device is not in reset mode.
RST
includes an internal pullup
current source. When
RST
is LOW, the sink current capability is
limited, allowing
RST
to be shorted to 5.0 V for software debug
or software download purposes.
INT
The Interrupt terminal
INT
is an output that is set LOW when
an interrupt occurs.
INT
is enabled using the Interrupt Register
(INTR). When
INT
occurs,
INT
stays LOW until the
INT
source
is cleared.
INT
output also reports a wake-up event by a 10
μ
s typical
pulse when the device is in stop mode.
V2
The V2 terminal is the input sense of the V2 regulator. It is
connected to the external ballast transistor. V2 is also the 5.0 V
supply of the internal CAN interface. It is possible to connect V2
to an external 5.0 V regulator or to the V
DD
output when no
external ballast transistor is used. In this case, the V2CTRL
terminal must be left open. Refer to
Figure 28, 33742 Typical
Application Schematic
, page 46.
V2CTRL
The V2CTRL terminal is the output drive of the V2 regulator
connected to the external ballast transistor.
V
SUP
The V
SUP
terminal is the battery supply input of the device.
HS
The HS terminal is the internal high-side driver output. It is
internally protected against overcurrent and overtemperature.
L0, L1, L2, and L3
The L0:L3 input terminals can be connected to external
switches or any IC’s output. The state of the inputs can be read
by SPI. Theses inputs can be used as wake-up events when the
device is set in Sleep or Stop mode.
CANH and CANL
The CAN High and CAN Low terminals are the interfaces to
the CAN bus lines. They are controlled by TXD input level, and
the state of CANH and CANL is reported through RXD output.
A 60
impedance termination is connected between CANH
and CANL.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33790 | Two-Channel Distributed System Interface (DSI) Physical Interface Device(2通道分布式系统接口（DSI）物理接口) |
| MC33793 | Distributed System Interface (DSI) Sensor Interface(分布式系统接口（DSI）传感器接口) |
| MC33794 | Electric Field Imaging Device(电场成像设备) |
| MC33880 | Configurable Octal Serial Switch with Serial Peripheral Interface I/O(可配置的8串行开关,带串行外围I/O口(SPI)) |
| MC33882 | Six-Output Low-Side Switch with SPI and Parallel Input Control(带SPI和并口输入控制的6输出低端开关) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33742DW | 功能描述:网络控制器与处理器 IC SBC-E-HS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33742DWR2 | 功能描述:网络控制器与处理器 IC SBC-E-HS RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MC33742EP | 功能描述:CAN 接口集成电路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742EPR2 | 功能描述:CAN 接口集成电路 SBC_ECAN_HS RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MC33742PEG | 功能描述:CAN 接口集成电路 SBC-E-HS-CAN RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。