- 您现在的位置：买卖IC网 > PDF目录181332 > MC33797 (飞思卡尔半导体(中国)有限公司) Four Channel Squib Driver IC PDF资料下载
参数资料
| 型号： | MC33797 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | Four Channel Squib Driver IC |
| 中文描述： | 四通道爆管驱动IC |
| 文件页数： | 11/32页 |
| 文件大小： | 639K |
| 代理商： | MC33797 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33797
FUNCTIONAL DESCRIPTION
FUNCTIONAL DEVICE OPERATION
TX: Request loop-to-loop short command ($E0–$E3)
RX: Previous executed command information.
TX: Request another command sequence.
RX: Receive loop-to-loop results from test.
CROSS-COUPLED SQUIB IC FUNCTION
The cross-coupled application utilizes the high- and low-
side squib drivers from two different squib driver ICs (see
SPI interface, the squib IC will maintain the capability to
conduct standard diagnostics (short-to-battery, short-to-
ground, short between squibs, and squib diagnostics)
between two different squib ICs. The squib IC must maintain
the capability to fire the squib drivers with the ARM and FIRE
command in either cross-coupled or single IC applications.
When the firing squib driver IC is used in cross-coupled
applications, the low-side squib driver must be activated prior
to activating the high-side squib driver.
Cross-coupling the high- and low-side squib driver from
two different squib driver ICs must be done without interfering
with standard squib operations when the squib IC is used in
an application where the high- and low-side squib drivers are
located on the same IC.
All remaining diagnostic functions will operate standard in
either a cross-coupled or single IC applications. These
functions include RR_DIAG, RR_LIMIT_X, High side, VVFIRE_XX,
VVFIRE_RTN, VTRANSTX, squib current timing measurement,
and FEN_1 and FEN_2 diagnostics.
The SENSE_1A (1B, 2A, or 2B) terminal squib IC #1 is
connected to SQB_LO_1A (1B, 2A, or 2B) terminal squib
driver IC #2 and is used to feed the diagnostic signal for
determining squib resistance and short-to-battery/ground
conditions (see Figure 8, page 17). During a fire event, the
fire current passes from squib driver IC #1 high-side driver
though the squib to squib driver IC #2 low-side driver. In the
cross-coupled mode, the squib driver IC #2 $C2
(SQUIB_LO_1A_CONT, [1B, 2A, or 2B]) command will be
used to check continuity of the low-side driver from the
SQB_LO_1A (1B, 2A, or 2B) terminal to the low-side driver
FET.
The low-side driver continuity is checked during the
continuity test. The driver continuity information will be
cleared after the information is transmitted on the next valid
SPI command.
EXAMPLE—CROSS-COUPLED SQUIB COMMAND
SPI SEQUENCE FROM MICROCONTROLLER
TX: Squib IC #1 request squib 1A resistance measurement
($D0).
RX: Previous executed command information.
TX: Run another command on the same squib IC #1.
RX: Receive measured squib 1A resistance information.
TX: Squib IC #1 request continuity command ($C2).
RX: Previous executed command information.
TX: Squib IC #2 request continuity command ($C2).
RX: Previous executed command information.
TX: Squib IC #2 request continuity command ($C2).
RX: Receive low-side driver continuity information for low-
side drivers which reside on IC #2.
TX: Squib IC #1 request another command sequence.
RX: Receive low-side driver continuity information for low-
side drivers that reside on IC #1.
TX: Squib IC #1 request loop-to-loop short command
($E0–$E3)
RX: Previous executed command information.
TX: Squib IC #2 request loop to loop short command for
other ICs ($E8).
RX: Previous executed command information.
TX: Squib IC #2 request loop-to-loop short command for
other ICs ($E8).
RX: Receive loop-to-loop results from test run on IC #1.
TX: Squib IC #1 request another command sequence.
RX: Receive loop-to-loop results from test run on IC #1.
FIRING A SQUIB
The firing of a squib driver requires the FEN_1 and FEN_2
terminals to be high and two separate 8-bit writes be made to
the shift register. With FEN_1 terminal high, squibs 1A and
1B can be armed and fired. With FEN_2 terminal high,
squibs 2A and 2B can be armed and fired. The first write is to
ARM squib drivers in preparation of receiving the fire
command. Squib 1A and squib 1B can be armed separately
from squib 2A and squib 2B (refer to Table 6) or all squibs
can be fired at once (refer to Table 7). All ARM and 5X (Fire)
commands will be echoed back on the SPI Data output.
Table 6. Squib Firing Commands
Hex Code
Command Description
A0 ARM Squib Drivers 1A and 1B
A1 ARM Squib Drivers 2A and 2B
相关PDF资料 |
PDF描述 |
|---|---|
| MC44C402 | MTS Stereo Encoder |
| MC44C402AC | MTS Stereo Encoder |
| MC44C402ACR2 | MTS Stereo Encoder |
| MC54HCT174AJ | HCT SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, CDIP16 |
| MC56F8367MPY60 | 16-BIT, 120 MHz, OTHER DSP, PQFP160 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33797BPEW | 功能描述:功率驱动器IC Four Channel Squib Dr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MC33797BPEWR2 | 功能描述:功率驱动器IC Four Channel Squib Dr RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MC33813AE | 功能描述:功率驱动器IC 1 CYL SM ENG CONTROL IC RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MC33813AER2 | 功能描述:功率驱动器IC 1 CYL SM ENG CONTROL IC RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MC33814AE | 功能描述:功率驱动器IC 2 CYL SM ENG CONTROL IC RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。