- 您现在的位置：买卖IC网 > PDF目录359133 > MC33886 (飞思卡尔半导体(中国)有限公司) 5.0 A H-Bridge(5.0A H桥接器) PDF资料下载
参数资料
| 型号： | MC33886 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | 5.0 A H-Bridge(5.0A H桥接器) |
| 中文描述： | 5.0的H -桥（5.0AH桥接器） |
| 文件页数： | 15/20页 |
| 文件大小： | 637K |
| 代理商： | MC33886 |
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33886
15
SYSTEM/APPLICATION INFORMATION
INTRODUCTION
Numerous protection and operational features (speed,
torque, direction, dynamic braking, and PWM control), in
addition to the 5.0 A current capability, make the 33886 a very
attractive, cost-effective solution for controlling a broad range of
fractional horsepower DC motors. A pair of 33886 devices can
be used to control bipolar stepper motors in both directions. In
addition, the 33886 can be used to control permanent magnet
solenoids in a push-pull variable force fashion using PWM
control. The 33886 can also be used to excite transformer
primary windings with a switched square wave to produce
secondary winding AC currents.
As shown in
Figure 1
, Simplified Internal Block Diagram,
page 2, the 33886 is a fully protected monolithic H-Bridge with
Fault Status reporting. For a DC motor to run the input
conditions need be as follows: D1 input logic Low, D2 input logic
High, FS flag cleared (logic High), with one IN logic Low and the
other IN logic High to define output polarity. The 33886 can
execute dynamic braking by simultaneously turning on either
both high-side
MOSFETs or both low-side MOSFETs in the
output H-Bridge; e.g., IN1 and IN2 logic High or IN1 and IN2
logic Low.
The 33886 outputs are capable of providing a continuous DC
load current of 5.0 A from a 40 V V+ source. An internal charge
pump supports PWM frequencies up to 10 kHz. An external
pull-up resistor is required for the open drain FS terminal for
fault status reporting.
Two independent inputs (IN1 and IN2) provide control of the
two totem-pole half-bridge outputs. Two disable inputs (D1 and
D2) are for forcing the H-Bridge outputs to a high impedance
state (all H-Bridge switches OFF).
The 33886 has undervoltage shutdown with automatic
recovery, active current limiting, output short-circuit latch-OFF,
and overtemperature latch-OFF. An undervoltage shutdown,
output short circuit latch-OFF, or overtemperature latch-OFF
fault condition will cause the outputs to turn OFF (i.e., become
high impedance or tri-stated) and the fault output flag to be set
Low. Either of the Disable inputs or V+ must be “toggled” to
clear the fault flag.
The short circuit/overtemperature shutdown scheme is
unique and best described as using a junction temperature-
dependent active current “fold back” protection scheme. When
a short circuit condition is experienced, the current limited
output is “ramped down” as the junction temperature increases
above 160
°
C, until at 175
°
C the current has decreased to about
2.5 A. Above 175
°
C, overtemperature shutdown (latch-OFF)
occurs. This feature allows the device to remain in operation for
a longer time with unexpected loads, while still retaining
adequate protection for both the device and the load.
FUNCTIONAL TERMINAL DESCRIPTION
PGND and AGND
Power and analog ground terminals. The power and analog
ground terminals should be connected together with a very low
impedance connection.
V+
V+ terminals are the power supply inputs to the device. All V+
terminals must be connected together on the printed circuit
board with as short as possible traces offering as low
impedance as possible between terminals.
V+ terminals have an undervoltage threshold. If the supply
voltage drops below a V+ undervoltage threshold, the output
power stage switches to a tri-state condition and the fault status
flag is set and the Fault Status terminal voltage switched to a
logic Low. When the supply voltage returns to a level that is
above the threshold, the power stage automatically
resumes
normal operation according to the established condition of the
input terminals and the fault status flag is automatically reset
logic High.
Fault Status (FS)
This terminal is the device fault status output. This output is
an active Low open drain structure requiring a pull-up resistor to
5.0 V. Refer to
Table 1, Truth Table
, page 14.
IN1, IN2, D1, and D2
These terminals are input control terminals used to control
the outputs. These terminals are 5.0 V CMOS-compatible
inputs with hysteresis. The IN1 and IN2 independently control
OUT1 and OUT2, respectively. D1 and D2 are complimentary
inputs used to tri-state disable the H-Bridge outputs.
When either D1 or D2 is set (D1 = logic High or D2 = logic
Low) in the disable state, outputs OUT1 and OUT2 are both tri-
state disabled; however, the rest of the device circuitry is fully
operational and the supply I
Q(standby)
current is reduced to a few
milliamperes. Refer to
Table 1, Truth Table
,
and
STATIC
ELECTRICAL CHARACTERISTICS
table, page 5.
F
Freescale Semiconductor, Inc.
Go to: www.freescale.com
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33887 | 5.0 A H-Bridge with Load Current Feedback(带本地电流反馈功能的5.0A H桥接器) |
| MC33888FB | Quad High Side and Octal Low Side Switch for Automotive Applications(4高端开关及8低端开关，用于自动应用) |
| MC33889 | System Basis Chip (SBC) with Low Speed Fault Tolerant CAN Interface |
| MC33897 | Single-Wire CAN Transceiver(单线CAN收发器) |
| MC33972 | Multiple Switch Detection Interface with Suppressed Wake-Up(带抑制唤醒功能的多开关检测接口) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33886DH | 功能描述:IC H-BRIDGE 5.0A OUTPUT 20-HSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| MC33886DHR2 | 功能描述:IC H-BRIDGE 5.0A 20-HSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| MC33886PVW | 功能描述:马达/运动/点火控制器和驱动器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33886PVWR2 | 功能描述:马达/运动/点火控制器和驱动器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33886VW | 功能描述:马达/运动/点火控制器和驱动器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。