- 您现在的位置：买卖IC网 > PDF目录359133 > MC33886 (飞思卡尔半导体(中国)有限公司) 5.0 A H-Bridge(5.0A H桥接器) PDF资料下载
参数资料
| 型号： | MC33886 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | 5.0 A H-Bridge(5.0A H桥接器) |
| 中文描述： | 5.0的H -桥（5.0AH桥接器） |
| 文件页数： | 16/20页 |
| 文件大小： | 637K |
| 代理商： | MC33886 |
33886
16
Go to: www.freescale.com
OUT1 and OUT2
These terminals are the outputs of the H-Bridge with
integrated output FET body diodes. The bridge output is
controlled using the IN1, IN2, D1, and D2 inputs. The outputs
have active current limiting above 6.5 A. The outputs also have
thermal shutdown (tri-state latch-OFF) with hysteresis as well
as short circuit latch-OFF protection.
A disable timer (time t
b
) incorporated to detect currents that
are higher than active current limit is activated at each output
activation to facilitate detecting hard output short conditions
(see
Figure 7
, page 9).
C
CP
Charge pump output terminal. A filter capacitor (up to 33 nF)
can be connected from the
C
CP
terminal and PGND. The device
can operate without the external capacitor, although the
C
CP
capacitor helps to reduce noise and allows the device to
perform at maximum speed, timing, and PWM frequency.
PERFORMANCE FEATURES
Short Circuit Protection
If an output short circuit condition is detected, the power
outputs tri-state (latch-OFF) independent of the input (IN1 and
IN2) states, and the fault status output flag is set logic Low. If
the D1 input changes from logic High to logic Low, or if the
D2
input changes from logic Low to logic High, the output bridge
will become operational again and the fault status flag will be
reset (cleared) to a logic High state.
The output stage will always switch into the mode defined by
the input terminals (IN1, IN2, D1, and D2), provided the device
junction temperature is within the specified operating
temperature.
Active Current Limiting
The maximum current flow under normal operating
conditions is internally limited to I
LIM
(5.2 A to 7.8 A). When the
maximum current value is reached, the output stages are tri-
stated for a fixed time (t
a
) of 20
μ
s typical. Depending on the
time constant associated with the load characteristics, the
current decreases during the tri-state duration until the next
output ON cycle occurs (see
Figures 7
and
13
, page 9 and
page 12, respectively).
The current limiting threshold value is dependent upon the
device junction temperature. When -40
°
C < T
J
< 160
°
C, I
LIM
is
between 5.2 A and 7.8 A. When T
J
exceeds 160
°
C, the
I
LIM
current decreases linearly down to 2.5 A typical at 175
°
C.
Above 175
°
C the device overtemperature circuit detects T
LIM
and overtemperature shutdown occurs (see
Figure 5
, page 8).
This feature allows the device to remain operational for a longer
time but at a regressing output performance level at junction
temperatures above 160
°
C.
Overtemperature Shutdown and Hysteresis
If an overtemperature condition occurs, the power outputs
are tri-state (latched-OFF) independent of the input signals and
the fault status flag is set logic Low.
To reset from this condition, D1 must change from logic High
to logic Low, or D2 must change from logic Low to logic High.
When reset, the output stage switches ON again, provided that
the junction temperature is now below the overtemperature
threshold limit minus the hysteresis.
Note
Resetting from the fault condition will clear the fault
status flag.
Main Differences Compared to MC33186DH1
COD terminal has been removed. Terminal 8 is now a Do
Not Connect (DNC) terminal.
Terminal 20 is no longer connected in the 20 HSOP
package. It is now a DNC terminal.
R
DS(ON)
max at T
J
= 150°C is now 225 m
per each output
transistor.
Maximum temperature operation is now 160°C, as
minimum thermal shutdown temperature has increased.
Current regulation limiting foldback is implemented above
160°C T
J
.
Thermal resistance junction to case has been increased
from ~2.0°C/W to ~5.0°C/W.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33887 | 5.0 A H-Bridge with Load Current Feedback(带本地电流反馈功能的5.0A H桥接器) |
| MC33888FB | Quad High Side and Octal Low Side Switch for Automotive Applications(4高端开关及8低端开关，用于自动应用) |
| MC33889 | System Basis Chip (SBC) with Low Speed Fault Tolerant CAN Interface |
| MC33897 | Single-Wire CAN Transceiver(单线CAN收发器) |
| MC33972 | Multiple Switch Detection Interface with Suppressed Wake-Up(带抑制唤醒功能的多开关检测接口) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33886DH | 功能描述:IC H-BRIDGE 5.0A OUTPUT 20-HSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| MC33886DHR2 | 功能描述:IC H-BRIDGE 5.0A 20-HSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| MC33886PVW | 功能描述:马达/运动/点火控制器和驱动器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33886PVWR2 | 功能描述:马达/运动/点火控制器和驱动器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MC33886VW | 功能描述:马达/运动/点火控制器和驱动器 5.0 A H-BRIDGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。