- 您现在的位置：买卖IC网 > PDF目录11717 > MC33972TEW (Freescale Semiconductor)IC SWITCH DETECT SPI 32-SOIC PDF资料下载
参数资料
| 型号： | MC33972TEW |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 13/32页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DETECT SPI 32-SOIC |
| 标准包装： | 42 |
| 应用： | 开关监控 |
| 接口： | SPI 串行 |
| 电源电压： | 3.1 V ~ 5.25 V |
| 封装/外壳： | 32-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 32-SOIC |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
33972
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
The scan timer sets the polling period between input
switch reads in Sleep mode. The period is set in the sleep
command and may be set to 000 (no period) to 111 (64 ms).
In Sleep mode when the scan timer expires, inputs will
behave as programmed prior to sleep command. The 33972
will wake up for approximately 125
μs and read the switch
inputs. At the end of the 125
μs, the input switch states are
compared with the switch state prior to sleep command.
When switch state changes are detected, an interrupt is
generated (when enabled; refer to wake-up/interrupt
command description on page 15), and the device enters
Normal mode. Without switch state changes, the 33972 will
reset the scan timer, inputs become tri-state, and the Sleep
mode continues until the scan timer expires again.
Table 20 shows the programmable settings of the Scan
timer.
Note The interrupt and scan timers are disabled in the
Normal Mode.
Figure 5, page 9, is a graphical description of how the
33972 device exits Sleep mode and enters Normal mode.
Notice that the device will exit Sleep mode when the interrupt
timer expires or when a switch change of state occurs. The
falling edge of INT triggers the MCU to wake from Sleep
state. Figure 12 illustrates the current consumed during
Sleep mode. During the 125
μs, the device is fully active and
switch states are read. The quiescent current is calculated by
integrating the normal running current over scan period plus
approximately 60
μA.
Figure 12. Sleep Current Waveform
TEMPERATURE MONITOR
With multiple switch inputs closed and the device
programmed with the wetting current timers disabled,
considerable power will be dissipated by the IC. For this
reason, temperature monitoring has been implemented. The
temperature monitor is active in the Normal mode only. When
the IC temperature is above the thermal limit, the temperature
monitor will do all of the following:
Generate an interrupt.
Force all 16 mA pull-up and pull-down current sources
to revert to 2.0 mA current sources.
Maintain the 2.0 mA current source and all other
functionality.
Set the thermal flag bit in the SPI output register.
The thermal flag bit in the SPI word will be cleared on rising
edge of CS provided the die temperature has cooled below
the thermal limit. When die temperature has cooled below
thermal limit, the device will resume previously programmed
settings.
Table 19. Interrupt Timer
Bits 543
Interrupt Period
000
32 ms
001
64 ms
010
128 ms
011
256 ms
100
512 ms
101
1.024 s
110
2.048 s
111
No interrupt wake-up
Table 20. Scan Timer
Bits 210
Scan Period
000
No Scan
001
1.0 ms
010
2.0 ms
011
4.0 ms
100
8.0 ms
101
16 ms
110
32 ms
111
64 ms
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
I = V/R or 0.270V/100
Ω = 2.7mA
Inputs active for
125
μs out of 32ms
I = V/R or
6.0mV/100
Ω = 60μA
相关PDF资料 |
PDF描述 |
|---|---|
| V150A28E500B | CONVERTER MOD DC/DC 28V 500W |
| MS3101A36-1P | CONN RCPT 22POS FREE HNG W/PINS |
| VE-B0H-IX-F3 | CONVERTER MOD DC/DC 52V 75W |
| MS3126F16-26PY | CONN PLUG 26POS STRAIGHT W/PINS |
| V150A24E500BL3 | CONVERTER MOD DC/DC 24V 500W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33972TEWR2 | 功能描述:接口 - 专用 MULTI-SW DETECT W/SUPRES RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33975ATEK | 功能描述:接口 - 专用 ENHANCED MULTI SW DETECT RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33975ATEKR2 | 功能描述:接口 - 专用 ENHANCED MULTI SW DETECT RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33975EK | 功能描述:多路器开关 IC EMSDI RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MC33975EKR2 | 功能描述:多路器开关 IC EMSDI RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。