- 您现在的位置：买卖IC网 > PDF目录1851 > MC33981BPNAR2 (Freescale Semiconductor)IC SWITCH HI SIDE SINGLE 16-PQFN PDF资料下载
参数资料
| 型号： | MC33981BPNAR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/40页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH HI SIDE SINGLE 16-PQFN |
| 标准包装： | 1,200 |
| 类型： | 高端 |
| 输入类型： | PWM |
| 输出数： | 1 |
| 导通状态电阻： | 4 毫欧 |
| 电源电压： | 6 V ~ 27 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-PowerDFN |
| 供应商设备封装： | 16-PQFN（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
FUNCTIONAL DEVICE OPERATION
PROTECTION AND DIAGNOSTIC FEATURES
directly but rather its effects on the low side MOSFET. When
V DLS > V OCLS , the GLS pin goes to 0 V and the OCLS
internal current source is disconnected and OCLS goes to
0 V. The GLS pin and the OCLS pin are reset (and the fault
is delatched) by a logic [0] at the INLS pin for at least
t RST(DIAG) . Figure 13 and Figure 14 illustrate the behavior in
case of overload on the low side gate driver.
When connected to an external resistor, the OCLS pin with
its internal current source sets the V OCLS level. By changing
the external resistance, the protection level can be adjusted
depending on low side characteristics. A 33 k ? resistor gives
a V DS level of 3.3 V typical.
This protection circuitry measures the voltage between the
drain of the low side (DLS pin) and the 33981 ground (GND
pin). For this reason it is key that the low side source, the
33981 ground, and the external resistance ground
connection are connected together in order to prevent false
error detection due to ground shifts.
The maximum OCLS voltage being 4.0 V, a resistor bridge
on DLS must be used to detect a higher voltage across the
low side.
CONFIGURATION
The CONF pin manages the cross-conduction between
the internal MOSFET and the external low side MOSFET.
With the CONF pin at 0 V, the two MOSFETs can be
independently controlled. A load can be placed between the
high side and the low side.
With the CONF pin at 5.0 V, the two MOSFETs cannot be
on at the same time. They are in half-bridge configuration as
shown in the 33981 Simplified Application Diagram . If INHS
and INLS are at 5.0 V at the same time, INHS has priority and
OUT will be at V PWR . If INHS changes from 5.0 V to 0 V with
INLS at 5.0 V, GLS will go to high state as soon as the V GS
of the internal MOSFET is lower than 2.0 V typically. A half-
bridge application could consist in sending PWM signal to the
INHS pin and 5.0 V to the INLS pin with the CONF pin at
5.0 V.
the 33981 Simplified Application Diagram with a DC motor
and external low side. The CONF and INLS pins are at 5.0 V.
When INHS is at 5.0 V, current is flowing in the motor. When
INHS goes to 0 V, the load current recirculates in the external
low side.
BOOTSTRAP SUPPLY
Bootstrap supply provides current to charge the bootstrap
capacitor through the V PWR pin. A short time is required after
the application of power to the device to charge the bootstrap
capacitor . A typical value for this capacitor is 100 nF. An
internal charge pump allows continuous MOSFET drive.
When the device is in the sleep mode, this bootstrap supply
is off to minimize current consumption.
HIGH SIDE GATE DRIVER
The high side gate driver switches the bootstrap capacitor
voltage to the gate of the MOSFET. The driver circuit has a
low-impedance drive to ensure that the MOSFET remains
OFF in the presence of fast falling dV/dt transients on the
OUT pin.
This bootstrap capacitor connected between the power
supply and the C BOOT pin provides the high pulse current to
drive the device. The voltage across this capacitor is limited
to about 13 V typical.
An external capacitor connected between pins SR and
GND is used to control the slew rate at the OUT pin. Figure 9
and Figure 10 give V OUT rise and fall time versus different SR
capacitors.
LOW SIDE GATE DRIVER
The low side control circuitry is PWM capable. It can drive
a standard MOSFET with an R DS(ON) as low as 10.0 m ? at a
frequency up to 60 kHz. The V GS is internally clamped at
12 V typically to protect the gate of the MOSFET. The GLS
pin is protected against short by a local over-temperature
sensor.
THERMAL FEEDBACK
The 33981 has an analog feedback output (TEMP pin) that
provides a value in inverse proportion to the temperature of
the GND flag (pin 13). The controlling microcontroller can
“read” the temperature proportional voltage with its analog-
to-digital converter (ADC). This can be used to provide real-
time monitoring of the PC board temperature to optimize the
motor speed and to protect the whole electronic system.
TEMP pin value is V TFEED with a negative temperature
coefficient of DT FEED .
REVERSE BATTERY
The 33981 survives the application of reverse battery
voltage as low as -16 V. Under these conditions, the output’s
gate is enhanced to decrease device power dissipation. No
additional passive components are required. The 33981
survives these conditions until the maximum junction rating is
reached.
In the case of reverse battery in a half-bridge application,
a direct current passes through the external freewheeling
diode and the internal high side.
As Figure 11 shows, it is essential to protect this power
line. The proposed solution is an external N-channel low side
with its gate tied to battery voltage through a resistor. A high
side in the V PWR line could be another solution.
33981
Analog Integrated Circuit Device Data ?
Freescale Semiconductor
17
相关PDF资料 |
PDF描述 |
|---|---|
| MC33984BPNAR2 | IC SWITCH HI SIDE DUAL 16-PQFN |
| MC33988CPNA | IC SWITCH HIGH SIDE DUAL 16QFN |
| MC33997DW | IC SWITCH 3.3/5V SUPPLY 24-SOIC |
| MC34063AD | IC REG BUCK BOOST INV 1.5A 8SOP |
| MC34063AMELG | IC REG BUCK BST INV ADJ 8SOEIAJ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33982BPNA | 功能描述:电源开关 IC - 配电 SPSS RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33982BPNAR2 | 功能描述:电源开关 IC - 配电 SPSS RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33982CHFK | 功能描述:电源开关 IC - 配电 SNGL 2MOHMS RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33982CHFKR2 | 功能描述:电源开关 IC - 配电 SNGL 2MOHMS RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33982CPNA | 制造商:Freescale Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。