- 您现在的位置：买卖IC网 > PDF目录359133 > MC33990 (飞思卡尔半导体(中国)有限公司) J-1850 SERIAL TRANSCEIVER(J-1850总线收发器) PDF资料下载
参数资料
| 型号： | MC33990 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | J-1850 SERIAL TRANSCEIVER(J-1850总线收发器) |
| 中文描述： | 歼1850串行收发器（的J - 1850总线收发器） |
| 文件页数： | 11/16页 |
| 文件大小： | 455K |
| 代理商： | MC33990 |
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33990
11
APPLICATIONS
Class B Module Inputs
Transmitter Data from the MCU (Tx)
The Tx input is a push-pull (N-channel/P-channel FETs)
buffer with hysteresis for noise immunity purposes. This pin is a
5.0 V CMOS logic level input from the MCU following a true
logic protocol. A logic [0] input drives the BUS
output to 0 V (via
the external pull-down resistor to ground on each node), while
a logic [1] input produces a high voltage at the BUS
output. A
logic [0] input level is guaranteed when the Tx input pin is open-
circuited by virtue of an internal 40 k
pull-down resistor. No
external resistor is required for its operation.
Waveshaping and 4X/Loop
This input is a tristateable input: 0 V = normal waveshaping,
5.0 V = waveshaping is disabled for 4X transmitting, and high
impedance = loopback mode of operation. This is a logic level
input used to select whether waveshaping for the Class B
output is enabled or disabled. A logic [0] enables waveshaping,
while a logic [1] disables waveshaping. In the 4X mode, the
BUS
output rise time is less than 2.0 μs and the fall time is less
than 5.0 μs (owing to the external RC pull-down to ground). In
the loopback condition, the Tx signal is fed back to the Rx
output
after
waveshaping
without
being transmitted onto the
BUS. This mode of operation is useful for system diagnostic
purposes.
Class B Module Outputs
Transceiver Output (BUS)
This is the output driver stage that sources current to the bus.
Its output follows the waveshaped waveform input. Its output
voltage is limited to 6.25 V to 8.0 V under normal battery level
conditions. The limited level is controlled by an internal
regulator/clamp circuit. Once the battery voltage drops below
9.0 V, the regulator/clamp circuit saturates, causing the bus
voltage to track the battery voltage. A 1.5 k
±
5% external
resistor (as well as any 10.6 k
pull-down resistors of any
secondary nodes) sinks the current to discharge the capacitors
during high-to-low transitions. This sourcing output is short
circuit-protected (60 mA to 170 mA) against a short to -2.0 V
and sinks less than 1.0 mA when shorted to V
BAT
. If a short
occurs, the overtemperature shutdown circuit protects the
source driver of the device. In the event battery power is lost to
the assembly, the bus transmitter's output stage will be disabled
and the leakage current from the BUS
output will not source or
sink more than 100 μA of current. The transceiver will operate
with a remote ground offset of
±
2.0 V, but the lower corners of
transmission will
not
be rounded during this condition.
Receiver Output to the Microcontroller (Rx)
This is a 5.0 V CMOS compatible push-pull output used to
send received data to the microcontroller. It does not require an
external pull-up resistor to be used. The receiver is always
enabled and draws less than 65 μA of current from V
BAT
. The
receive threshold is dependent on the state of the
SLEEP
pin.
The receiver circuitry is able to operate with V
BAT
voltages as
low as 4.25 V and still remains capable of “waking up” the
33990 when remote Class B activity is detected.
When the
SLEEP
pin is 0 V and message activity occurs on
the bus, the receiver passes the bus
message through to the
microcontroller. The 33990 does not automatically “wake up”
from a sleep state when bus
activity occurs: the microcontroller
must tell it to do so.
In the Static Electrical Characteristics table, the maximum
voltage for Rx is specified as 4.75 V over an operating range of
-40
°
C to 125
°
C temperature and 7.0 V to 16 V V
BAT
. This
maximum Rx voltage is compatible with the minimum V
DD
voltage of microcontrollers to prevent the 33990 from sourcing
current to the microcontroller's output.
Switched Ground Output (LOAD)
Normally this output is a saturated switch to ground, which
pulls down the external resistor between the BUS and LOAD
outputs. In the event ground is lost to the assembly, the LOAD
output will bias itself “off” and will not leak more than 100 μA of
current out of this pin.
Overtemperature Shutdown
If the
BUS output becomes shorted to ground for any
duration, an overtemperature shutdown circuit “latches off” the
output source transistor whenever the die temperature exceeds
150
°
C to 190
°
C. The output transistor remains latched off until
the Tx input is toggled from a logic [0] to a logic [1]. The rising
edge provides the clearing function, provided the locally sensed
temperature is 10
°
C to 15
°
C below the latch-off temperature trip
temperature.
Table 1. Class B Bus Capacitance and Resistance Expressions
Level
Capacitance
Resistance to Ground
Minimum
(3.3 x 0.9) + (0.47 x 0.9) = 3.39 nF
(1.5 x 0.95) || (10.6 x 0.95) / 25 = 314
Maximum
(3.3 x 1.1) + 25(0.47 x 1.1) = 16.55 nF
(1.5 x 1.05) || (10.6 x 1.05) = 1.38 k
F
Freescale Semiconductor, Inc.
Go to: www.freescale.com
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33991 | Gauge Driver Integrated Circuit(标尺驱动器集成电路) |
| MC33993 | Multiple Switch Detection Interface(多开关监测接口) |
| MC33997 | Switching Power Supply with Linear Regulators(带线性稳压器的开关电源) |
| MC33998 | Switching Power Supply with Linear Regulators(带线性稳压器的开关电源) |
| MC34017 | Telephone Tone Ringer(电话振铃) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33990D | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33990DR2 | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33991DW | 制造商:Freescale Semiconductor 功能描述:Gauge Driver Integrated Circuit |
| MC33991DWR2 | 制造商:Rochester Electronics LLC 功能描述:GUAGE DRIVER IC - Bulk |
| MC33993DWB | 功能描述:接口 - 专用 MSDI RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。