- 您现在的位置：买卖IC网 > PDF目录359133 > MC33990 (飞思卡尔半导体(中国)有限公司) J-1850 SERIAL TRANSCEIVER(J-1850总线收发器) PDF资料下载
参数资料
| 型号： | MC33990 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | J-1850 SERIAL TRANSCEIVER(J-1850总线收发器) |
| 中文描述： | 歼1850串行收发器（的J - 1850总线收发器） |
| 文件页数： | 12/16页 |
| 文件大小： | 455K |
| 代理商： | MC33990 |
33990
12
Go to: www.freescale.com
Waveshaping
Waveshaping is incorporated into the 33990 to minimize
radiated EMI emissions.
Receiver Protocol
The Class B communication scheme uses a variable pulse
width (VPW) protocol. The microcontroller provides the VPW
decoding function. Once the receiver detects a transition on Rx,
it starts an internal counter. The initial “start of frame” bit is a
logic [1] and lasts 200 μs. For subsequent bits, if there is a bus
transition before 96 μs, one logic state is inferred. If there is a
bus transition after 96 μs, the other logic state is inferred. The
“end of data” bit is a logic [0] and lasts 200 μs. If there is no
activity on the bus for 280 μs to 320 μs following a broadcast
message, multiple unit nodes may arbitrate for control of the
next message. During an arbitration, after the “start of frame” bit
has been transmitted, the secondary node transmitting the
most consecutive logic [0] bits will be granted sole transmission
access to the bus for that message.
Loss of Assembly Ground Connection
The definition of a loss of assembly ground condition at the
device level is that all pins of the 33990, with the exception of
BUS and LOAD, see a very low impedance to V
BAT
.
The LOAD pin of the device has an internal transistor switch
connected to it that is normally saturated to ground. This pulls
the LOAD-side of the external resistor (tied from BUS to LOAD)
to ground under normal conditions. The LOAD pin switch is
essentially that of an “upside down” FET, which is normally
biased “on” so long as module ground is present and biased
“off” when loss-of-ground occurs. When a loss of assembly
ground occurs, the load transistor switch is self-biased “off”,
allowing no more than 100 μA of leakage current to flow in the
LOAD pin. During such a loss of assembly ground condition, the
BUS and LOAD pins exhibit a high impedance to V
BAT
; all other
pins will exhibit a low impedance to V
BAT
. During this condition
the BUS pin is prevented from sourcing any current or loading
the bus, which would cause a corruption of any data being
transmitted on the bus. While a particular assembly is
experiencing a loss of ground, all other assembly nodes are
permitted to function normally. It should be noted that with other
nodes existing on the bus, the bus will always have some
minimum/maximum impedance to ground as shown in Table 1,
page 11.
Loss of Assembly Battery Connection
The definition of a loss of assembly battery condition at the
device level is that the V
BAT
pin of the 33990 sees an infinite
impedance to V
BAT
, but there is some undefined impedance
between these pins and ground.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33991 | Gauge Driver Integrated Circuit(标尺驱动器集成电路) |
| MC33993 | Multiple Switch Detection Interface(多开关监测接口) |
| MC33997 | Switching Power Supply with Linear Regulators(带线性稳压器的开关电源) |
| MC33998 | Switching Power Supply with Linear Regulators(带线性稳压器的开关电源) |
| MC34017 | Telephone Tone Ringer(电话振铃) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33990D | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33990DR2 | 功能描述:IC TRANSCEIVER J-1850 BUS 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| MC33991DW | 制造商:Freescale Semiconductor 功能描述:Gauge Driver Integrated Circuit |
| MC33991DWR2 | 制造商:Rochester Electronics LLC 功能描述:GUAGE DRIVER IC - Bulk |
| MC33993DWB | 功能描述:接口 - 专用 MSDI RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。