- 您现在的位置：买卖IC网 > PDF目录359133 > MC33993 (飞思卡尔半导体(中国)有限公司) Multiple Switch Detection Interface(多开关监测接口) PDF资料下载
参数资料
| 型号： | MC33993 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | Multiple Switch Detection Interface(多开关监测接口) |
| 中文描述： | 多交换检测接口（多开关监测接口） |
| 文件页数： | 18/28页 |
| 文件大小： | 820K |
| 代理商： | MC33993 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
33993/D
18
Go to: www.freescale.com
Example of Normal Mode Operation
The operation of the device in Normal Mode is defined by the
states of the programmable internal control registers. A typical
application may have the following settings:
Programmable Switch – Set to Switch-to-Ground
All Inputs Set as Wake-Up
Wetting Current On (16 mA)
Wetting Current Timer On (20 ms)
All inputs Tri-State-Disabled (comparator is active)
Analog select 00000 (no input channel selected)
With the device programmed as above, an interrupt will be
generated with each switch contact change of state (open-to-
close or close-to-open) and 16 mA of contact wetting current
will be source for 20 ms. The
INT
pin will remain low until switch
status is acknowledged by the microprocessor. It is critical to
understand
INT
will not be cleared on the rising edge of
CS
if a
switch closure occurs while
CS
is low. The maximum duration a
switch state change can exist without acknowledgement
depends on the software response time to the interrupt.
Figure 4
, page 8, shows the interaction between changing input
states and the
INT
and
CS
pins.
If desired the user may disable interrupts (
wake up/interrupt
command
) from the 33993 device and read the switch states on
a periodic basis. Switch activation and deactivation faster than
the MCU read rate will not be acknowledged.
The 33993 device will exit the Normal mode and enter the
Sleep mode only with a valid sleep command.
Sleep Mode
Sleep mode is used to reduce system quiescent currents.
Sleep mode may be entered only by sending the
sleep
command.
All register settings programmed in Normal mode
will be maintained in Sleep mode.
The 33993 will exit Sleep mode and enter Normal mode
when any of the following events occur:
Input Switch Change of State (when enabled)
Interrupt Timer Expire
Falling Edge of
WAKE
Falling Edge of
INT
(with V
DD
= 5.0 V and
WAKE
at
Logic [1])
Falling Edge of
CS
(with V
DD
= 5.0 V)
Power-ON Reset (POR)
The V
DD
supply may be removed from the device during
Sleep mode. However removing V
DD
from the device in Sleep
mode will disable a wake-up from falling edge of
INT
and
CS
.
Note
In cases where
CS
is used to wake the device, the first
SO data message is not valid.
The sleep command contains settings for two programmable
timers for Sleep mode, the interrupt timer and the scan timer, as
shown in
Table 13
.
The interrupt timer is used as a periodic wake-up timer.
When the timer expires, an interrupt is generated and the
device enters Normal mode.
Table 14
shows the
programmable settings of the Interrupt timer.
Table 13. Sleep Command
Sleep Command
Command Bits
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
0
0
0
1
1
0
0
X
X
X
X
X
X
X
X
X
X
i
i
i
s
s
s
Table 14. Interrupt Timer
Bits 543
Interrupt Period
000
32 ms
001
64 ms
010
128 ms
011
256 ms
100
512 ms
101
1.024 s
110
2.048 s
111
4.096 s
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33997 | Switching Power Supply with Linear Regulators(带线性稳压器的开关电源) |
| MC33998 | Switching Power Supply with Linear Regulators(带线性稳压器的开关电源) |
| MC34017 | Telephone Tone Ringer(电话振铃) |
| MC34063A | DC-DC CONVERTER CONTROL CIRCUITS |
| MC34063AB | DC-DC CONVERTER CONTROL CIRCUITS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33993DWB | 功能描述:接口 - 专用 MSDI RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33993DWBR2 | 功能描述:接口 - 专用 MSDI RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33996EK | 功能描述:电源开关 IC - 配电 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33996EKR2 | 功能描述:电源开关 IC - 配电 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33997DW | 功能描述:IC SWITCH 3.3/5V SUPPLY 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。