- 您现在的位置：买卖IC网 > PDF目录359133 > MC33993 (飞思卡尔半导体(中国)有限公司) Multiple Switch Detection Interface(多开关监测接口) PDF资料下载
参数资料
| 型号： | MC33993 |
| 厂商： | 飞思卡尔半导体(中国)有限公司 |
| 英文描述： | Multiple Switch Detection Interface(多开关监测接口) |
| 中文描述： | 多交换检测接口（多开关监测接口） |
| 文件页数： | 9/28页 |
| 文件大小： | 820K |
| 代理商： | MC33993 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
33993/D
9
SYSTEM/APPLICATION INFORMATION
INTRODUCTION
The 33993 device is an integrated circuit designed to provide
systems with ultra-low quiescent sleep/wake-up modes and a
robust interface between switch contacts and a
microprocessor. The 33993 replaces many of the discrete
components required when interfacing to microprocessor-
based systems while providing switch ground offset protection,
contact wetting current, and system wake-up.
The 33993 features 8-programmable switch-to-ground or
switch-to-battery inputs and 14 switch-to-ground inputs. All
switch inputs may be read as analog inputs through the analog
multiplexer (AMUX). Other features include a programmable
wake-up timer, programmable interrupt timer, programmable
wake-up/interrupt bits, and programmable wetting current
settings.
This device is designed primarily for automotive applications
but may be used in a variety of other applications such as
computer, telecommunications, and industrial controls.
FUNCTIONAL PIN DESCRIPTION
CS
The system MCU selects the 33993 to receive
communication using the chip select (
CS
) pin. With the
CS
in a
logic low state, command words may be sent to the 33993 via
the serial input (SI) pin, and switch status information can be
received by the MCU via the serial output (SO) pin. The falling
edge of
CS
enables the SO output, latches the state of the
INT
pin, and the state of the external switch inputs.
Rising edge of the
CS
initiates the following operation:
1. Disables the SO driver (high impedance)
2.
INT
pin is reset to logic [1], except when additional switch
changes occur during
CS
low. (See
Figure 4
on page 8.)
3. Activates the received command word, allowing the
33993 to act upon new data from switch inputs.
To avoid any spurious data, it is essential the high-to-low and
low-to-high transitions
of the
CS
signal occur only when SCLK
is in a logic low state. Internal to the 33993 device is an active
pull-up to V
DD
on
CS
.
In Sleep mode the negative edge of
CS
(V
DD
applied) will
wake up the 33993 device. Data received from the device
during
CS
wake-up may not be accurate.
SCLK
The system clock (SCLK) pin clocks the internal shift register
of the 33993. The SI data is latched into the input shift register
on the falling edge of SCLK signal. The SO pin shifts the switch
status bits out on the rising edge of SCLK. The SO data is
available for the MCU to read on the falling edge of SCLK. False
clocking of the shift register must be avoided to ensure validity
of data. It is essential the SCLK pin be in a logic low state
whenever
CS
makes any transition. For this reason, it is
recommended, though not necessary, that the SCLK pin is
commanded to a low logic state as long as the device is not
accessed and
CS
is in a logic high state. When the
CS
is in a
logic high state, any signal on the SCLK and SI pins will be
ignored and the SO pin is tri-state.
SI
The SI pin is used for serial instruction data input. SI
information is latched into the input register on the falling edge
of SCLK. A logic high state present on SI will program a
one
in
the command word on the rising edge of the
CS
signal. To
program a complete word, 24 bits of information must be
entered into the device.
SO
The SO pin is the output from the shift register. The SO pin
remains tri-stated until the
CS
pin transitions to a logic low state.
All
open switches
are reported as
zero
, all
closed switches
are
reported as
one
. The negative transition of
CS
enables the SO
driver.
The first positive transition of SCLK will make the status data
bit 24 available on the SO pin. Each successive positive clock
will make the next status data bit available for the MCU to read
on the falling edge of SCLK. The SI/SO shifting of the data
follows a first-in-first-out protocol, with both input and output
words transferring the most significant bit (MSB) first.
INT
The
INT
pin is an interrupt output from the 33993 device. The
INT
pin is an open-drain output with an internal pull-up to V
DD
.
In Normal mode, a switch state change will trigger the
INT
pin
(when enabled). The
INT
pin and INT bit in the SPI register are
latched on the falling edge of
CS
. This permits the MCU to
determine the origin of the interrupt. When two 33993 devices
are used, only the device initiating the interrupt will have the
INT bit set. The
INT
pin is cleared on the rising edge of
CS
. The
INT
pin will not clear with rising edge of
CS
if a switch contact
change has occurred while
CS
was low.
In a multiple 33993 device system with
WAKE
high and V
DD
on (Sleep mode), the falling edge of
INT
will place all 33993s in
Normal mode.
F
Freescale Semiconductor, Inc.
Go to: www.freescale.com
n
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC33997 | Switching Power Supply with Linear Regulators(带线性稳压器的开关电源) |
| MC33998 | Switching Power Supply with Linear Regulators(带线性稳压器的开关电源) |
| MC34017 | Telephone Tone Ringer(电话振铃) |
| MC34063A | DC-DC CONVERTER CONTROL CIRCUITS |
| MC34063AB | DC-DC CONVERTER CONTROL CIRCUITS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33993DWB | 功能描述:接口 - 专用 MSDI RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33993DWBR2 | 功能描述:接口 - 专用 MSDI RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33996EK | 功能描述:电源开关 IC - 配电 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33996EKR2 | 功能描述:电源开关 IC - 配电 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33997DW | 功能描述:IC SWITCH 3.3/5V SUPPLY 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。