- 您现在的位置：买卖IC网 > PDF目录11717 > MC33993DWBR2 (Freescale Semiconductor)IC SWITCH I/O INTERFACE 32-SOIC PDF资料下载
参数资料
| 型号： | MC33993DWBR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH I/O INTERFACE 32-SOIC |
| 标准包装： | 1,000 |
| 系列： | * |
| 应用： | * |
| 接口： | * |
| 电源电压： | * |
| 封装/外壳： | 32-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 32-SOIC |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Analog Integrated Circuit Device Data
Freescale Semiconductor
23
33993
TYPICAL APPLICATIONS
INTRODUCTION
ARCHIVE
INFORMATION
ARCHIVE
INFORMATION
from first device is connected to SI of second device). With
two devices, 48 clock pulses are required to shift data in.
When the WAKE feature is used to enable the power supply,
both WAKE pins should be connected to the enable pin on
the power supply. The INT pins may be connected to one
interrupt pin on the MCU or may have their own dedicated
interrupt to the MCU.
The transition from Normal to Sleep mode is done by
sending the sleep command. With the devices connected in
serial and the sleep command sent, both will enter Sleep
mode on the rising edge of CS. When Sleep mode is entered,
the WAKE pin will be logic [1]. If either device wakes up, the
WAKE pin will transition low, waking the other device.
A condition exists where the MCU is sending the sleep
command (CS logic [0]) and a switch input changes state.
With this event the device that detects this input will not
transition to Sleep mode, while the second device will enter
Sleep mode. In this case two switch status commands must
be sent to receive accurate switch status data. The first
switch status command will wake the device in Sleep mode.
Switch status data may not be valid from the first switch
status command because of the time required for the input
voltage to rise above the 4.0 V input comparator threshold.
This time is dependant on the impedance of SGn or SPn
node. The second switch status command will provide
accurate switch status information. It is recommended that
software wait 10 ms to 20 ms between the two switch status
commands, allowing time for switch input voltages to
stabilize. With all switch states acknowledged by the MCU,
the sleep sequence may be initiated. All parameters for Sleep
mode should be updated prior to sending the sleep
command.
The 33993 IC has an internal 5.0 V supply from VPWR pin.
A POR circuit monitors the internal 5.0 V supply. In the event
of transients on the VPWR pin, an internal reset may occur.
Upon reset the 33993 will enter Normal mode with the
internal registers as defined in Table 14, page 16. Therefore
it is recommended that the MCU periodically update all
registers internal to the IC.
USING THE WAKE FEATURE
The 33993 provides a WAKE output and wake-up input
designed to control an enable pin on system power supply.
While in the Normal mode, the WAKE output is low, enabling
the power supply. In the Sleep mode, the WAKE pin is high,
disabling the power supply. The WAKE pin has a passive
pull-up to the internal 5.0 V supply but may be pulled up
When the WAKE output is not used the pin should be
pulled up to the VDD supply through a resistor as shown in
During the Sleep mode, a switch closure will set the WAKE
pin low, causing the 33993 to enter the Normal mode. The
power supply will then be activated, supplying power to the
VDD pin and the microprocessor and the 33993. The
microprocessor can determine the source of the wake-up by
reading the interrupt flag.
COST AND FLEXIBILITY
Systems requiring a significant number of switch
interfaces have many discrete components. Discrete
components on standard PWB consume board space and
must be checked for solder joint integrity. An integrated
approach reduces solder joints, consumes less board space,
and offers wider operating voltage, analog interface
capability, and greater interfacing flexibility.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484P18F35P | CONN PLUG 66POS STRAIGHT W/PINS |
| VE-B04-IX-F4 | CONVERTER MOD DC/DC 48V 75W |
| VE-B04-IX-F3 | CONVERTER MOD DC/DC 48V 75W |
| D38999/20JF32SA | CONN RCPT 32POS WALL MNT W/SCKT |
| MCZ33094EGR2 | IC IGNITION CONTROL 12V 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33996EK | 功能描述:电源开关 IC - 配电 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33996EKR2 | 功能描述:电源开关 IC - 配电 16LOW SIDE SW 1.2OHM RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MC33997DW | 功能描述:IC SWITCH 3.3/5V SUPPLY 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| MC33997DWR2 | 制造商:Rochester Electronics LLC 功能描述:MLPS 3.3 IC - Bulk |
| MC33999EK | 功能描述:多路器开关 IC 16 LOW SIDE PWM&SPI RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。