- 您现在的位置：买卖IC网 > PDF目录1948 > MC56F8322VFAE (Freescale Semiconductor)IC DSP 16BIT 60MHZ 48-LQFP PDF资料下载
参数资料
| 型号： | MC56F8322VFAE |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 38/136页 |
| 文件大小： | 0K |
| 描述： | IC DSP 16BIT 60MHZ 48-LQFP |
| 标准包装： | 250 |
| 系列： | 56F8xxx |
| 核心处理器： | 56800E |
| 芯体尺寸： | 16-位 |
| 速度： | 60MHz |
| 连通性： | CAN，SCI，SPI |
| 外围设备： | POR，PWM，温度传感器，WDT |
| 输入/输出数： | 21 |
| 程序存储器容量： | 40KB（20K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 6K x 16 |
| 电压 - 电源 (Vcc/Vdd)： | 2.25 V ~ 3.6 V |
| 数据转换器： | A/D 6x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 48-LQFP |
| 包装： | 托盘 |
| 配用： | MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页
56F8322 Techncial Data, Rev. 16
132
Freescale Semiconductor
Preliminary
The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimizing the size of the clearance is important to minimize the change in
thermal performance caused by removing part of the thermal interface to the heat sink. Because of the
experimental difficulties with this technique, many engineers measure the heat sink temperature and then
back-calculate the case temperature using a separate measurement of the thermal resistance of the
interface. From this case temperature, the junction temperature is determined from the junction-to-case
thermal resistance.
12.2 Electrical Design Considerations
Use the following list of considerations to assure correct operation of the 56F8322/56F8122:
Provide a low-impedance path from the board power supply to each VDD pin on the device and from the
board ground to each VSS (GND) pin
The minimum bypass requirement is to place six 0.01–0.1
μF capacitors positioned as close as possible to
the package supply pins. The recommended bypass configuration is to place one bypass capacitor on each
of the VDD/VSS pairs, including VDDA/VSSA. Ceramic and tantalum capacitors tend to provide better
tolerances.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS (GND)
pins are less than 0.5 inch per capacitor lead
Use at least a four-layer Printed Circuit Board (PCB) with two inner layers for VDD and VSS
Bypass the VDD and VSS layers of the PCB with approximately 100μF, preferably with a high-grade
capacitor such as a tantalum capacitor
Because the device’s output signals have fast rise and fall times, PCB trace lengths should be minimal
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or electrical
fields. However, normal precautions are advised to
avoid
application
of
any
voltages
higher
than
maximum-rated voltages to this high-impedance circuit.
Reliability of operation is enhanced if unused inputs are
tied to an appropriate voltage level.
相关PDF资料 |
PDF描述 |
|---|---|
| MC56F8323VFBE | IC MPU HYBRID DSP 32K 64-LQFP |
| MC56F8335VFGE | IC DIGITAL SIGNAL CTLR 128-LQFP |
| MC56F8345MFGE | IC DSP 16BIT 60MHZ 128-LQFP |
| MC56F8346VFVE | IC DSP 16BIT 60MHZ 144-LQFP |
| MC56F8366VFVE | IC DSP 16BIT 60MHZ 144-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC56F8322VFAER2 | 功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT HYBRID CNTRLR RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| MC56F8323 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers |
| MC56F8323EVM | 功能描述:开发板和工具包 - 其他处理器 MC56F832X Dev Kit RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| MC56F8323EVM | 制造商:Freescale Semiconductor 功能描述:Tools Development kit Kit Con |
| MC56F8323EVME | 功能描述:开发板和工具包 - 其他处理器 MC56F8323 EVAL BRD RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。