参数资料
型号: MC68HC705P6ACDW
厂商: Freescale Semiconductor
文件页数: 38/98页
文件大小: 0K
描述: IC MCU 2.1MHZ 4.5K OTP 28-SOIC
标准包装: 26
系列: HC05
核心处理器: HC05
芯体尺寸: 8-位
速度: 2.1MHz
连通性: SIO
外围设备: POR,WDT
输入/输出数: 21
程序存储器容量: 4.5KB(4.5K x 8)
程序存储器类型: OTP
RAM 容量: 176 x 8
电压 - 电源 (Vcc/Vdd): 3 V ~ 5.5 V
数据转换器: A/D 4x8b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 28-SOIC(0.295",7.50mm 宽)
包装: 管件
SIOP Registers
MC68HC705P6A Advance Information Data Sheet, Rev. 2.1
Freescale Semiconductor
43
7.3 SIOP Registers
The SIOP is programmed and controlled by the SIOP control register (SCR) located at address $000A,
the SIOP status register (SSR) located at address $000B, and the SIOP data register (SDR) located at
address $000C.
7.3.1 SIOP Control Register (SCR)
This register is located at address $000A and contains two bits. Figure 7-3 shows the position of each bit
in the register and indicates the value of each bit after reset.
SPE — Serial Peripheral Enable
When set, the SPE bit enables the SIOP subsystem such that SDO/PB5 is the serial data output,
SDI/PB6 is the serial data input, and SCK/PB7 is a serial clock input in the slave mode or a serial clock
output in the master mode. Port B DDR and data registers can be manipulated as usual (except for
PB5); however, these actions could affect the transmitted or received data.
The SPE bit is readable at any time. However, writing to the SIOP control register while a transmission
is in progress will cause the SPIF and DCOL bits in the SIOP status register (see below) to operate
incorrectly. Therefore, the SIOP control register should be written once to enable the SIOP and then
not written to until the SIOP is to be disabled. Clearing the SPE bit while a transmission is in progress
will 1) abort the transmission, 2) reset the serial bit counter, and 3) convert the port B/SIOP port to a
general-purpose I/O port. Reset clears the SPE bit.
MSTR — Master Mode Select
When set, the MSTR bit configures the serial I/O port for master mode. A transfer is initiated by writing
to the SDR. Also, the SCK pin becomes an output providing a synchronous data clock dependent upon
the oscillator frequency. When the device is in slave mode, the SDO and SDI pins do not change
function. These pins behave exactly the same in both the master and slave modes.
The MSTR bit is readable and writeable at any time regardless of the state of the SPE bit. Clearing the
MSTR bit will abort any transfers that may have been in progress. Reset clears the MSTR bit as well
as the SPE bit, disabling the SIOP subsystem.
Address:
$000A
Bit 7
654321
Bit 0
Read:
0
SPE
0
MSTR
0000
Write:
Reset:
00000000
= Unimplemented
Figure 7-3. SIOP Control Register (SCR)
相关PDF资料
PDF描述
C8051F336-GM IC MCU 16K FLASH 20QFN
EHFWX2B CONN EEE1394 FMAL T/H CROSS BLK
MC68HC705KJ1CDW IC MCU 4MHZ 1.2K OTP 16-SOIC
MC68HC705J1ACP IC MCU 4MHZ 1.2K OTP 20-DIP
LPC11U12FBD48/201, IC MCU 32BIT 16K 48LQFP
相关代理商/技术参数
参数描述
MC68HC705P6ACP 功能描述:IC MCU 2.1MHZ 4.5K OTP 28-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C,IrDA,LIN,SPI,UART/USART 外围设备:DMA,PDR,POR,PVD,PWM,温度传感器,WDT 输入/输出数:26 程序存储器容量:64KB(64K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN,36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND
MC68HC705P6ADW 制造商:Rochester Electronics LLC 功能描述:MCU, 176 BYTES RAM, A/D - Bulk
MC68HC705P6AMDW 功能描述:IC MCU 4.6K OTP 2.1MHZ 28-SOIC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC05 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN,SCI,SPI 外围设备:POR,PWM,温度传感器,WDT 输入/输出数:21 程序存储器容量:40KB(20K x 16) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC705P6AMP 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HC705P6CDW 制造商:Motorola Inc 功能描述: