- 您现在的位置：买卖IC网 > PDF目录132965 > MC68HC711EA9CFS2 (FREESCALE SEMICONDUCTOR INC) 8-BIT, UVPROM, 2 MHz, MICROCONTROLLER, CQCC52 PDF资料下载
参数资料
| 型号： | MC68HC711EA9CFS2 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, UVPROM, 2 MHz, MICROCONTROLLER, CQCC52 |
| 封装： | WINDOWED, CERAMIC, LCC-52 |
| 文件页数： | 9/58页 |
| 文件大小： | 583K |
| 代理商： | MC68HC711EA9CFS2 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
MC68HC11EA9
MOTOROLA
MC68HC11EA9TS/D
17
5.
Clear the PGM bit to turn off the VPPE voltage.
6.
Clear all bits in the PPROG register to reconfigure the EPROM address and data buses for nor-
mal operation.
NOTE
PROG mode is initiated when RESET, MODA, and MODB pins are pulled low (the
pin state required to enter bootstrap mode). This means that if these three pins are
pulled low and VPPE is present on the XIRQ pin, the EPROM will be programmed.
To prevent this, place a pull-up resistor on the IRQ pin (CE pin in PROG mode).
When the device goes into reset, the PGM bit is forced to the voltage disable state
(EPGM = 0) before the address/data latches are enabled to the external input lines.
Only after this occurs is voltage control returned to the IRQ pin.
4.9.3 Programming EPROM with Downloaded Data
When using this method, the EPROM is programmed by software while in the special test or bootstrap
modes. User-developed software can be uploaded through the SCI, or a ROM resident EPROM pro-
gramming utility can be used. To use the resident utility, bootload a three-byte program consisting of a
single jump instruction to $BF00. $BF00 is the starting address of a resident EPROM programming util-
ity. The utility program sets the X and Y index registers to default values, then receives programming
data from an external host and puts it in EPROM. The value in IX determines programming delay time.
The value in IY is a pointer to the first address in EPROM to be programmed (default = $D000).
When the utility program is ready to receive programming data, it sends the host the $FF character.
Then it waits. When the host sees the $FF character, the EPROM programming data is sent, starting
with the first location in the EPROM array. After the last byte to be programmed is sent and the corre-
sponding verification data is returned, the programming operation is terminated by resetting the MCU.
* MC68HC711EA9 only.
ODD — Program Odd Rows in Half of EEPROM (TEST)
Refer to 4.10 EEPROM.
EVEN — Program Even Rows in Half of EEPROM (TEST)
Refer to 4.10 EEPROM.
ELAT — EPROM/OTPROM Latch Control
When ELAT = 1, writes to EPROM cause address and data to be latched and the EPROM/OTPROM
cannot be read. ELAT can be read any time. ELAT can be written any time except when EPGM = 1;
then the write to ELAT is disabled. For MC68HC711EA9, EPGM enables the high voltage necessary
for both EPROM/OTPROM and EEPROM programming. For MC68HC711EA9 ELAT and EELAT are
mutually exclusive and cannot both equal one.
0 = EPROM address and data bus configured for normal reads
1 = EPROM address and data bus configured for programming
BYTE — Byte/Other EEPROM Erase Mode
Refer to 4.10 EEPROM.
ROW — Row/All EEPROM Erase Mode
Refer to 4.10 EEPROM.
PPROG — EPROM and EEPROM Programming Control Register
$103B
BIT 7
654321
BIT 0
ODD
EVEN
ELAT*
BYTE
ROW
ERASE
EELAT
PGM
RESET:
00000001
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711EA9CP3 | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP56 |
| MC68HC711EA9MFN2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PQCC52 |
| M30280F8HP-D9 | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| M306NKME-XXXGP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| M306NMME-XXXGP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP128 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC711K4CFN4 | 功能描述:IC MCU 24K OTP 4MHZ 84-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC711K4CFNE3 | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC711K4CFNE4 | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC711K4CFU4 | 功能描述:IC MCU 24K 4MHZ EEPROM 80-QFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C，IrDA，LIN，SPI，UART/USART 外围设备:DMA，PDR，POR，PVD，PWM，温度传感器，WDT 输入/输出数:26 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN，36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND |
| MC68HC711KS2CPU4 | 制造商:Motorola Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。