- 您现在的位置：买卖IC网 > PDF目录132965 > MC68HC711EA9CP3 (FREESCALE SEMICONDUCTOR INC) 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP56 PDF资料下载
参数资料
| 型号： | MC68HC711EA9CP3 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 3 MHz, MICROCONTROLLER, PDIP56 |
| 封装： | PLASTIC, SDIP-56 |
| 文件页数： | 4/58页 |
| 文件大小： | 583K |
| 代理商： | MC68HC711EA9CP3 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
MOTOROLA
MC68HC11EA9
12
MC68HC11EA9TS/D
IRV(NE) — Internal Read Visibility(Not E)
IRVNE can be written once in any mode. In expanded modes, IRVNE determines whether IRV is on or
off. In special test mode, IRVNE is reset to one. In all other modes, IRVNE is reset to zero.
0 = No internal read visibility on external bus
1 = Data from internal reads is driven out the external data bus.
In single-chip modes this bit determines whether the E clock drives out from the chip.
0 = E is driven out from the chip.
1 = E pin is driven low. Refer to the following table.
PSEL[3:0] — Priority Select Bits [3:0]
Refer to 5 Resets and Interrupts
4.6 RAM
In all modes RAM is enabled and present at locations $0000–$01FF. The RAM can be mapped to any
1-Kbyte boundary by writing an appropriate value to the INIT register. The INIT register must be written
during the first 64 cycles after reset in expanded and single-chip modes. If RAM and the register block
are placed at the same 1-Kbyte boundary, the first 64 bytes of RAM are inaccessible. This is due to an
on-chip hardware priority scheme which eliminates conflicts which could arise from multiple resources
sharing address locations. Figure 6 shows the location of the RAM array.
4.7 Bootstrap ROM
When operating in normal modes (SMOD = 0), the bootstrap ROM is disabled and removed from the
memory map. In bootstrap and special test modes, bootstrap ROM is present at $BF00–$BFFF. Boot-
strap ROM cannot be remapped to other locations. Figure 6 shows the location of the bootstrap ROM
array.
The bootstrap ROM contains a small program that allows program code to be downloaded into on-chip
RAM. When the MC68HC(7)11EA9 enters bootstrap mode, bootloader firmware residing in bootstrap
ROM begins the downloading procedure by initializing the SCI system and transmitting a break out the
SCI TxD pin. The SCI then waits for the first character to be received. After the first character is received
on the RxD pin of the SCI, bootloader firmware begins counting the number of bytes received. When
an idle time of four characters or the character for address $01FF is received, the bootloader program
terminates the download and control is passed to the loaded program at $0000. For a detailed descrip-
tion of the M68HC11 bootstrap mode, refer to application note
M68HC11 Bootstrap Mode (AN1060/D).
4.8 Memory Map and Register Block
The operating mode determines memory mapping and whether external addresses can be accessed.
Memory locations for on-chip resources are the same for both expanded and single-chip modes. Con-
trol bits in the CONFIG register allow ROM/EPROM and EEPROM to be disabled from the memory
map. The RAM is mapped to $0000 after reset. It can be placed at any 4 Kbyte boundary ($x000) by
writing an appropriate value to the INIT register. The 64-byte register block is mapped to $1000 after
reset and can also be placed at any 4 Kbyte boundary ($x000) by writing an appropriate value to the
INIT register. If RAM and registers are mapped to the same boundary, the first 64 bytes of RAM will be
inaccessible. Table 4 shows the arrangement of control registers and bits within the register block.
Table 3 IRVNE Control vs. Operating Mode
Operating
Mode
IRVNE Bit
Out of Reset
E Clock
Out of Reset
IRV Function
Out of Reset
IRVNE Bit
Affects Only
Single Chip
0
On
Off
E
Expanded
0
On
Off
IRV
Bootstrap
0
On
Off
E
Special Test
1
On
IRV
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC711EA9MFN2 | 8-BIT, OTPROM, 2 MHz, MICROCONTROLLER, PQCC52 |
| M30280F8HP-D9 | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| M306NKME-XXXGP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP100 |
| M306NMME-XXXGP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP128 |
| M306NMMG-XXXGP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP128 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC711K4CFN4 | 功能描述:IC MCU 24K OTP 4MHZ 84-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC711K4CFNE3 | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC711K4CFNE4 | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC711K4CFU4 | 功能描述:IC MCU 24K 4MHZ EEPROM 80-QFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 其它有关文件:STM32F101T8 View All Specifications 特色产品:STM32 32-bit Cortex MCUs 标准包装:490 系列:STM32 F1 核心处理器:ARM? Cortex?-M3 芯体尺寸:32-位 速度:36MHz 连通性:I²C，IrDA，LIN，SPI，UART/USART 外围设备:DMA，PDR，POR，PVD，PWM，温度传感器，WDT 输入/输出数:26 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):2 V ~ 3.6 V 数据转换器:A/D 10x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:36-VFQFN，36-VFQFPN 包装:托盘 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名称:497-9032STM32F101T8U6-ND |
| MC68HC711KS2CPU4 | 制造商:Motorola Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。