参数资料
型号: MC68HCL05C9AFB
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP44
封装: QFP-44
文件页数: 132/160页
文件大小: 4128K
代理商: MC68HCL05C9AFB
Serial Communications Interface (SCI)
Functional Description
MC68HC05C9A Rev. 4.0
General Release Specification
Serial Communications Interface (SCI)
NON-DISCLOSURE
AGREEMENT
REQUIRED
interrupts are enabled). The transfer of data to the transmit data shift
register is synchronized with the bit rate clock (see Figure 9-2). All data
is transmitted least significant bit first. Upon completion of data
transmission, the transmission complete flag (TC) in the SCSR is set
(provided no pending data, preamble, or break is to be sent) and an
interrupt is generated (if the transmit complete interrupt is enabled). If
the transmitter is disabled, and the data, preamble, or break (in the
transmit data shift register) has been sent, the TC bit will be set also.
This will also generate an interrupt if the transmission complete interrupt
enable bit (TCIE) is set. If the transmitter is disabled during a
transmission, the character being transmitted will be completed before
the transmitter gives up control of the TDO pin.
When SCDR is read, it contains the last data byte received, provided
that the receiver is enabled. The receive data register full flag bit (RDRF)
in the SCSR is set to indicate that a data byte has been transferred from
the input serial shift register to the SCDR; this will cause an interrupt if
the receiver interrupt is enabled. The data transfer from the input serial
shift register to the SCDR is synchronized by the receiver bit rate clock.
The OR (overrun), NF (noise), or FE (framing) error flags in the SCSR
may be set if data reception errors occurred.
An idle line interrupt is generated if the idle line interrupt is enabled and
the IDLE bit (which detects idle line transmission) in SCSR is set. This
allows a receiver that is not in the wakeup mode to detect the end of a
message, or the preamble of a new message, or to re-synchronize with
the transmitter. A valid character must be received before the idle line
condition or the IDLE bit will not be set and idle line interrupt will not be
generated.
Figure 9-2. Rate Generator Division
OSC FREQ
(fOSC)
÷2
BUS FREQ
(fOP)
SCP0–SCP1
SCI PRESCALER
SELECT
N
SCR0–SCR2
SCI RATE
SELECT
M
÷16
SCI TRANS
CLOCK (TX)
SCI RECEIVE
CLOCK (RT)
CONTROL
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相关PDF资料
PDF描述
M901-01I690.5692 690.5692 MHz, OTHER CLOCK GENERATOR, CQCC36
MC68HC11E0VB2 8-BIT, 2 MHz, MICROCONTROLLER, PDIP56
MC68HC811E2MP2 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PDIP48
MC68HC908QT1MDW 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8
MC68020FC25E 32-BIT, 25 MHz, MICROPROCESSOR, PQFP132
相关代理商/技术参数
参数描述
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
MC68HCP11E0CP2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HCP11E0FN 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN,SCI,SPI 外围设备:POR,PWM,温度传感器,WDT 输入/输出数:21 程序存储器容量:40KB(20K x 16) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HCP11E0FNE 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT