- 您现在的位置：买卖IC网 > PDF目录80482 > MC7457RX1200LC (FREESCALE SEMICONDUCTOR INC) 32-BIT, 1200 MHz, RISC PROCESSOR, CBGA483 PDF资料下载
参数资料
| 型号： | MC7457RX1200LC |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, 1200 MHz, RISC PROCESSOR, CBGA483 |
| 封装： | 29 X 29 MM, 3.22 MM HEIGHT, 1.27 MM PITCH, CERAMIC, BGA-483 |
| 文件页数： | 51/72页 |
| 文件大小： | 1598K |
| 代理商： | MC7457RX1200LC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
MPC7457 RISC Microprocessor Hardware Specifications, Rev. 7
Freescale Semiconductor
55
System Design Information
9.6
Pull-Up/Pull-Down Resistor Requirements
The MPC7457 requires high-resistive (weak: 4.7-kΩ) pull-up resistors on several control pins of the bus
interface to maintain the control signals in the negated state after they have been actively negated and
released by the MPC7457 or other bus masters. These pins are: TS, ARTRY, SHDO, and SHD1.
Some pins designated as being for factory test must be pulled up to OVDD or down to GND to ensure
proper device operation. For the MPC7447, 360 BGA, the pins that must be pulled up to OVDD are:
LSSD_MODE and TEST[0:3]; the pins that must be pulled down to GND are: L1_TSTCLK and TEST[4].
For the MPC7457, 483 BGA, the pins that must be pulled up to OVDD are: LSSD_MODE and TEST[0:5];
the pins that must be pulled down are: L1_TSTCLK and TEST[6]. The CKSTP_IN signal should likewise
be pulled up through a pull-up resistor (weak or stronger: 4.7–1 kΩ) to prevent erroneous assertions of this
signal.
In addition, the MPC7457 has one open-drain style output that requires a pull-up resistor (weak or
stronger: 4.7–1 kΩ) if it is used by the system. This pin is CKSTP_OUT.
If pull-down resistors are used to configure BVSEL or L3VSEL, the resistors should be less than 250 Ω
(see Table 16). Because PLL_CFG[0:4] must remain stable during normal operation, strong pull-up and
pull-down resistors (1 kΩ or less) are recommended to configure these signals in order to protect against
erroneous switching due to ground bounce, power supply noise or noise coupling.
During inactive periods on the bus, the address and transfer attributes may not be driven by any master and
may, therefore, float in the high-impedance state for relatively long periods of time. Because the MPC7457
must continually monitor these signals for snooping, this float condition may cause excessive power draw
by the input receivers on the MPC7457 or by other receivers in the system. These signals can be pulled up
through weak (10-kΩ) pull-up resistors by the system, address bus driven mode enabled (see the MPC7450
RISC Microprocessor Family Users’ Manual for more information about this mode), or they may be
otherwise driven by the system during inactive periods of the bus to avoid this additional power draw.
Preliminary studies have shown the additional power draw by the MPC7457 input receivers to be
negligible and, in any event, none of these measures are necessary for proper device operation. The
snooped address and transfer attribute inputs are: A[0:35], AP[0:4], TT[0:4], CI, WT, and GBL.
If extended addressing is not used, A[0:3] are unused and must be pulled low to GND through weak
pull-down resistors. If the MPC7457 is in 60x bus mode, DTI[0:3] must be pulled low to GND through
weak pull-down resistors.
The data bus input receivers are normally turned off when no read operation is in progress and, therefore,
do not require pull-up resistors on the bus. Other data bus receivers in the system, however, may require
pull-ups, or that those signals be otherwise driven by the system during inactive periods by the system. The
data bus signals are: D[0:63] and DP[0:7].
Table 21. Impedance Characteristics
VDD = 1.5 V, OVDD = 1.8 V ± 5%, Tj = 5°–85°C
Impedance
Processor Bus
L3 Bus
Unit
Z0
Typical
33–42
34–42
Ω
Maximum
31–51
32–44
Ω
相关PDF资料 |
PDF描述 |
|---|---|
| MC3S12HZ32J3CAA | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP80 |
| MC9S12HZ64J3MAA | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80 |
| MB95F354EWQN-G-SNERE1 | MICROCONTROLLER, PQCC32 |
| MPC8560CPXAQFC | 32-BIT, 1000 MHz, RISC PROCESSOR, PBGA783 |
| M908-02I075.0000LF | 75 MHz, OTHER CLOCK GENERATOR, CQCC36 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC7457RX1200PB | 制造商:Freescale Semiconductor 功能描述:A7, 1.35V +50MV/-30MV - Trays |
| MC7457RX1267LB | 制造商:Freescale Semiconductor 功能描述:MPC74XX RISC 32-BIT 0.13UM 1.267GHZ 1.5V/1.8V/2.5V 483-PIN F - Trays |
| MC7457RX1267LC | 功能描述:微处理器 - MPU APOLO7 RV1.2 1.3V 105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| MC7457RX1333PB | 制造商:Freescale Semiconductor 功能描述:A7, 1.35V +50MV/-30MV - Trays |
| MC7457RX733NC | 功能描述:IC MPU RISC 32BIT 483FCCBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC74xx 标准包装:1 系列:MPC85xx 处理器类型:32-位 MPC85xx PowerQUICC III 特点:- 速度:1.2GHz 电压:1.1V 安装类型:表面贴装 封装/外壳:783-BBGA，FCBGA 供应商设备封装:783-FCPBGA（29x29） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。