参数资料
| 型号： | MC74HC4538ADR2 |
| 厂商： | ON Semiconductor |
| 文件页数： | 16/16页 |
| 文件大小： | 0K |
| 描述： | IC MULTIVIBRTR DUAL MONO 16SOIC |
| 标准包装： | 1 |
| 系列： | 74HC |
| 逻辑类型： | 单稳态 |
| 独立电路： | 2 |
| 施密特触发器输入： | 是 |
| 传输延迟： | 30ns |
| 输出电流高，低： | 5.2mA，5.2mA |
| 电源电压： | 2 V ~ 6 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 标准包装 |
| 其它名称： | MC74HC4538ADRODKR MC74HC4538ADRODKR-ND MC74HC4538ADROSDKR |
MC74HC4538A
http://onsemi.com
9
PIN DESCRIPTIONS
INPUTS
A1, A2 (Pins 4, 12)
Positiveedge trigger inputs. A risingedge signal on
either of these pins triggers the corresponding multivibrator
when there is a high level on the B1 or B2 input.
B1, B2 (Pins 5, 11)
Negativeedge trigger inputs. A fallingedge signal on
either of these pins triggers the corresponding multivibrator
when there is a low level on the A1 or A2 input.
Reset 1, Reset 2 (Pins 3, 13)
Reset inputs (active low). When a low level is applied to
one of these pins, the Q output of the corresponding
multivibrator is reset to a low level and the Q output is set to
a high level.
CX1/RX1 and CX2/RX2 (Pins 2 and 14)
External timing components. These pins are tied to the
common points of the external timing resistors and
capacitors (see the Block Diagram). Polystyrene capacitors
are recommended for optimum pulse width control.
Electrolytic capacitors are not recommended due to high
leakages associated with these type capacitors.
GND (Pins 1 and 15)
External ground. The external timing capacitors discharge
to ground through these pins.
OUTPUTS
Q1, Q2 (Pins 6, 10)
Noninverted monostable outputs. These pins (normally
low) pulse high when the multivibrator is triggered at either
the A or the B input. The width of the pulse is determined by
the external timing components, RX and CX.
Q1, Q2 (Pins 7, 9)
Inverted monostable outputs. These pins (normally high)
pulse low when the multivibrator is triggered at either the A
or the B input. These outputs are the inverse of Q1 and Q2.
+
+
RxCx
VCC
M1
2 k
W
M3
M2
A
B
RESET
POWER
ON
RESET
RESET LATCH
TRIGGER CONTROL
RESET CIRCUIT
TRIGGER
CONTROL CIRCUIT
OUTPUT
LATCH
UPPER
REFERENCE
CIRCUIT
Vre,
UPPER
LOWER
REFERENCE
CIRCUIT
Vre,
LOWER
Q
C
CB
Q
R
VCC
Figure 11. Logic Detail (1/2 the Device)
相关PDF资料 |
PDF描述 |
|---|---|
| MC14538BDWR2 | IC MULTIVIBRATR DUAL CMOS 16SOIC |
| VE-JWF-MW | CONVERTER MOD DC/DC 72V 100W |
| MC14538BDR2 | IC MULTIVIBRATR DUAL CMOS 16SOIC |
| VE-JWD-MW | CONVERTER MOD DC/DC 85V 100W |
| VE-JWB-MW | CONVERTER MOD DC/DC 95V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC74HC4538ADR2G | 功能描述:单稳态多谐振荡器 3-6V Dual Precision MonoStable RoHS:否 制造商:Texas Instruments 每芯片元件:1 逻辑系列:LVC 逻辑类型:Monostable Multivibrator 封装 / 箱体:SSOP-8 传播延迟时间:18.6 ns 高电平输出电流:- 32 mA 低电平输出电流:32 mA 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| MC74HC4538ADR2G-CUT TAPE | 制造商:ON 功能描述:MC74HC4538A Series 3 to 6 V Dual Precision Monostable Multivibrator - SOIC-16 |
| MC74HC4538ADTR2 | 功能描述:单稳态多谐振荡器 3-6V Dual Precision RoHS:否 制造商:Texas Instruments 每芯片元件:1 逻辑系列:LVC 逻辑类型:Monostable Multivibrator 封装 / 箱体:SSOP-8 传播延迟时间:18.6 ns 高电平输出电流:- 32 mA 低电平输出电流:32 mA 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| MC74HC4538ADTR2G | 功能描述:单稳态多谐振荡器 3-6V Dual Precision MonoStable RoHS:否 制造商:Texas Instruments 每芯片元件:1 逻辑系列:LVC 逻辑类型:Monostable Multivibrator 封装 / 箱体:SSOP-8 传播延迟时间:18.6 ns 高电平输出电流:- 32 mA 低电平输出电流:32 mA 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| MC74HC4538AF | 功能描述:单稳态多谐振荡器 3-6V Dual Precision RoHS:否 制造商:Texas Instruments 每芯片元件:1 逻辑系列:LVC 逻辑类型:Monostable Multivibrator 封装 / 箱体:SSOP-8 传播延迟时间:18.6 ns 高电平输出电流:- 32 mA 低电平输出电流:32 mA 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。