参数资料
型号: MC8610TVT1066JB
厂商: Freescale Semiconductor
文件页数: 76/96页
文件大小: 0K
描述: MPU E600 CORE 1066MHZ 783-PBGA
标准包装: 36
系列: MPC86xx
处理器类型: 32-位 MPC86xx PowerPC
速度: 1.066GHz
电压: 1V
安装类型: 表面贴装
封装/外壳: 783-BBGA,FCBGA
供应商设备封装: 783-FCPBGA(29x29)
包装: 托盘
MPC8610 Integrated Host Processor Hardware Specifications, Rev. 2
Hardware Design Considerations
Freescale Semiconductor
78
SerDes—Receiver lanes configured for PCI Express are allowed to be disconnected (as would occur when a PCI
Express slot is connected but not populated). Directions for terminating the SerDes signals is discussed in Section 3.10,
3.6
Pull-Up and Pull-Down Resistor Requirements
The MPC8610 requires weak pull-up resistors (2–10 k
Ω is recommended) on open drain type pins including I2C pins and PIC
interrupt pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 53.
Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most
have asynchronous behavior and spurious assertion will give unpredictable results.
Refer to the PCI 2.2 specification for all pull-ups required for PCI.
The following pins must not be pulled down during power-on reset: DIU_LD[5:6], MSRCID[1:2], HRESET_REQ, and
TRIG_OUT/READY.
The following are factory test pins and require strong pull up resistors (100
Ω – 1 kΩ) to OVDD: LSSD_MODE,
TEST_MODE[0:3].
The following pins require weak pull-up resistors (2–10 k
Ω) to their specific power supplies: LCS[0:4], LCS[5]/DMA_DREQ2,
LCS[6]/DMA_DACK[2], LCS[7]/DMA_DDONE[2], IRQ_OUT, IIC1_SDA, IIC1_SCL, IIC2_SDA, IIC2_SCL, and
CKSTP_OUT.
The following pins should be pulled to ground with a 100-
Ω resistor: SD1_IMP_CAL_TX, SD2_IMP_CAL_TX. The following
pins should be pulled to ground with a 200-
Ω resistor: SD1_IMP_CAL_RX, SD2_IMP_CAL_RX.
When the platform frequency is 400 MHz, cfg_platform_freq must be pulled down at reset. Also, cfg_dram_type[0 or 1] must
be valid at power-up even before HRESET assertion.
For other pin pull-up or pull-down recommendations of signals, see Section 1, “Pin Assignments and Reset States.
3.7
Output Buffer DC Impedance
The MPC8610 drivers are characterized over process, voltage, and temperature. For all buses, the driver is a push-pull
single-ended driver type (open drain for I
2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD or GND. Then, the
value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 51). The output impedance is the average of two
components, the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open) and
相关PDF资料
PDF描述
345-012-523-804 CARDEDGE 12POS DUAL .100 GREEN
MC8610PX1333JB MPU E600 CORE 1333MHZ 783-PBGA
345-012-523-802 CARDEDGE 12POS DUAL .100 GREEN
345-012-523-801 CARDEDGE 12POS DUAL .100 GREEN
MC8610PX1066JB MPU E600 CORE 1066MHZ 783-PBGA
相关代理商/技术参数
参数描述
MC8610TVT1066JZ 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications
MC8610TVT1067G 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610TVT1067J 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610TVT1333JB 制造商:Freescale Semiconductor 功能描述:MPC8XXX RISC 32-BIT 0.09UM 1.333GHZ 1.8V/2.5V/3.3V 783-PIN B - Bulk
MC8610TVT667FB 功能描述:微处理器 - MPU REV 1.1 8610 1.0V -40C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324