参数资料
型号: MC8610TVT1066JB
厂商: Freescale Semiconductor
文件页数: 85/96页
文件大小: 0K
描述: MPU E600 CORE 1066MHZ 783-PBGA
标准包装: 36
系列: MPC86xx
处理器类型: 32-位 MPC86xx PowerPC
速度: 1.066GHz
电压: 1V
安装类型: 表面贴装
封装/外壳: 783-BBGA,FCBGA
供应商设备封装: 783-FCPBGA(29x29)
包装: 托盘
MPC8610 Integrated Host Processor Hardware Specifications, Rev. 2
Hardware Design Considerations
Freescale Semiconductor
86
Tyco Electronics
800-522-6752
Chip Coolers
P.O. Box 3668
Harrisburg, PA 17105-3668
Internet: www.chipcoolers.com
Wakefield Engineering
603-635-5102
33 Bridge St.
Pelham, NH 03076
Internet: www.wakefield.com
Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal performance at a given air
velocity, spatial volume, mass, attachment method, assembly, and cost.
3.12.2.1
Internal Package Conduction Resistance
For the exposed-die packaging technology described in Table 62, the intrinsic conduction thermal resistance paths are as
follows:
The die junction-to-case thermal resistance
The die junction-to-board thermal resistance
Figure 55 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit board.
Figure 55. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
The heat sink removes most of the heat from the device. Heat generated on the active side of the chip is conducted through the
silicon, then through the heat sink attach material (or thermal interface material), and finally to the heat sink. The
junction-to-case thermal resistance is low enough that the heat sink attach material and heat sink thermal resistance are the
dominant terms.
3.12.2.2
Thermal Interface Materials
A thermal interface material is recommended at the package-to-heat sink interface to minimize the thermal contact resistance.
Figure 56 shows the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, fluoroether oil),
a bare joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal
interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the interface
thermal resistance. In contrast, the bare joint results in a thermal resistance approximately seven times greater than the thermal
grease joint.
External Resistance
Internal Resistance
Radiation
Convection
Radiation
Convection
Heat Sink
Printed-Circuit Board
Thermal Interface Material
Package/Leads
Die Junction
Die/Package
(Note the internal versus external package resistance.)
相关PDF资料
PDF描述
345-012-523-804 CARDEDGE 12POS DUAL .100 GREEN
MC8610PX1333JB MPU E600 CORE 1333MHZ 783-PBGA
345-012-523-802 CARDEDGE 12POS DUAL .100 GREEN
345-012-523-801 CARDEDGE 12POS DUAL .100 GREEN
MC8610PX1066JB MPU E600 CORE 1066MHZ 783-PBGA
相关代理商/技术参数
参数描述
MC8610TVT1066JZ 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications
MC8610TVT1067G 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610TVT1067J 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610TVT1333JB 制造商:Freescale Semiconductor 功能描述:MPC8XXX RISC 32-BIT 0.09UM 1.333GHZ 1.8V/2.5V/3.3V 783-PIN B - Bulk
MC8610TVT667FB 功能描述:微处理器 - MPU REV 1.1 8610 1.0V -40C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324