参数资料
型号: MC8641DVU1333JE
厂商: Freescale Semiconductor
文件页数: 117/130页
文件大小: 0K
描述: IC MPU DUAL CORE E600 1023FCCBGA
标准包装: 1
系列: MPC86xx
处理器类型: 32-位 MPC86xx PowerPC
速度: 1.333GHz
电压: 1.05V
安装类型: 表面贴装
封装/外壳: 1023-BCBGA,FCCBGA
供应商设备封装: 1023-FCCBGA(33x33)
包装: 托盘
MPC8641 and MPC8641D Integrated Host Processor Hardware Specifications, Rev. 2
Freescale Semiconductor
87
Serial RapidIO
link shall be active in both the transmit and receive directions, and opposite ends of the links shall use
asynchronous clocks. Four lane implementations shall use CJPAT as defined in Annex 48A. Single lane
implementations shall use the CJPAT sequence specified in Annex 48A for transmission on lane 0. The
amount of data represented in the eye shall be adequate to ensure that the bit error ratio is less than 10-12.
The eye pattern shall be measured with AC coupling and the compliance template centered at 0 Volts
differential. The left and right edges of the template shall be aligned with the mean zero crossing points of
the measured data eye. The load for this test shall be 100
Ω resistive +/– 5% differential to 2.5 GHz.
15.9.2
Jitter Test Measurements
For the purpose of jitter measurement, the effects of a single-pole high pass filter with a 3 dB point at (Baud
Frequency)/1667 is applied to the jitter. The data pattern for jitter measurements is the Continuous Jitter
Test Pattern (CJPAT) pattern defined in Annex 48A of IEEE 802.3ae. All lanes of the LP-Serial link shall
be active in both the transmit and receive directions, and opposite ends of the links shall use asynchronous
clocks. Four lane implementations shall use CJPAT as defined in Annex 48A. Single lane implementations
shall use the CJPAT sequence specified in Annex 48A for transmission on lane 0. Jitter shall be measured
with AC coupling and at 0 Volts differential. Jitter measurement for the transmitter (or for calibration of a
jitter tolerance setup) shall be performed with a test procedure resulting in a BER curve such as that
described in Annex 48B of IEEE 802.3ae.
15.9.3
Transmit Jitter
Transmit jitter is measured at the driver output when terminated into a load of 100
Ω resistive +/– 5%
differential to 2.5 GHz.
15.9.4
Jitter Tolerance
Jitter tolerance is measured at the receiver using a jitter tolerance test signal. This signal is obtained by first
producing the sum of deterministic and random jitter defined in Section 8.6 and then adjusting the signal
amplitude until the data eye contacts the 6 points of the minimum eye opening of the receive template
shown in Figure 8-4 and Table 8-11. Note that for this to occur, the test signal must have vertical waveform
symmetry about the average value and have horizontal symmetry (including jitter) about the mean zero
crossing. Eye template measurement requirements are as defined above. Random jitter is calibrated using
a high pass filter with a low frequency corner at 20 MHz and a 20 dB/decade roll-off below this. The
required sinusoidal jitter specified in Section 8.6 is then added to the signal and the test load is replaced
by the receiver being tested.
相关PDF资料
PDF描述
MC8641DHX1333JE IC DUAL CORE PROCESSOR 1023-CBGA
IDT70V9169L7PF IC SRAM 144KBIT 7NS 100TQFP
XC4028XL-1HQ160C IC FPGA C-TEMP 3.3V 1SPD 160HQFP
XC4028XL-1BG352I IC FPGA I-TEMP 3.3V 1SPD 352MBGA
IDT709359L7PF IC SRAM 144KBIT 7NS 100TQFP
相关代理商/技术参数
参数描述
MC8641DVU1333K 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8641DVU1333N 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8641DVU1500G 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8641DVU1500H 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8641DVU1500J 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications