参数资料
型号: MC9S08RG60CFJ
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
封装: LQFP-32
文件页数: 196/232页
文件大小: 2818K
代理商: MC9S08RG60CFJ
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页当前第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页第225页第226页第227页第228页第229页第230页第231页第232页
Resets, Interrupts, and System Configuration
MC9S08RC/RD/RE/RG
66
MOTOROLA
Figure 5-3 System Reset Status (SRS)
POR — Power-On Reset
Reset was caused by the power-on detection logic. Because the internal supply voltage was ramping
up at the time, the low-voltage reset (LVR) status bit is also set to indicate that the reset occurred while
the internal supply was below the LVR threshold.
1 = POR caused reset.
0 = Reset not caused by POR.
PIN — External Reset Pin
Reset was caused by an active-low level on the external reset pin.
1 = Reset came from external reset pin.
0 = Reset not caused by external reset pin.
COP — Computer Operating Properly (COP) Watchdog
Reset was caused by the COP watchdog timer timing out. This reset source may be blocked by
COPE = 0.
1 = Reset caused by COP timeout.
0 = Reset not caused by COP timeout.
ILOP — Illegal Opcode
Reset was caused by an attempt to execute an unimplemented or illegal opcode. The STOP instruction
is considered illegal if stop is disabled by STOPE = 0 in the SOPT register. The BGND instruction is
considered illegal if active background mode is disabled by ENBDM = 0 in the BDCSC register.
1 = Reset caused by an illegal opcode.
0 = Reset not caused by an illegal opcode.
ILAD — Illegal Address Access
Reset was caused by an attempt to access a designated illegal address.
1 = Reset caused by an illegal address access
0 = Reset not caused by an illegal address access
Bit 7
6
54321
Bit 0
Read:
NOTES:
1. The ILAD bit is only present in 16K and 8K versions of the devices.
0
0
Write:
Writing any value to SRS address clears COP watchdog timer.
Power-on reset:
1
0
000010
Low-voltage reset:
U
0
000010
Any other reset:
0
(2)
2. Any of these reset sources that are active at the time of reset will cause the corresponding bit(s) to be set;
bits corresponding to sources that are not active at the time of reset will be cleared.
(2)
000
U = Unaffected by reset
相关PDF资料
PDF描述
MC9S08RE60CFJ 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
MC9S08RE32CFJ 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32
MC9S08RD60CPE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP28
MC9S08RE60CFG 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
MC9S08RD16CFG 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44
相关代理商/技术参数
参数描述
MC9S08RG60CFJE 功能描述:8位微控制器 -MCU 9S08 2K RAM 60K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MC9S08RG60CFJER 制造商:Freescale Semiconductor 功能描述:9S08 2K RAM 60K FLASH - Tape and Reel
MC9S08RG60CPE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC9S08RG60DWE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers
MC9S08RG60FDE 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Microcontrollers