- 您现在的位置：买卖IC网 > Datasheet目录342 > MCB11C14 (Keil)BOARD EVAL FOR NXP LPC11C14 Datasheet资料下载
参数资料
| 型号： | MCB11C14 |
| 厂商： | Keil |
| 文件页数： | 11/49页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR NXP LPC11C14 |
| 产品培训模块： | Code Density for LPC11xx |
| 标准包装： | 1 |
| 类型： | MCU |
| 适用于相关产品： | LPC11C14 |
| 所含物品： | 板，线缆 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
NXP Semiconductors
LPC11C12/C14
? Four programmable interrupt priority levels, with hardware priority level masking.
? Relocatable vector table.
? Software interrupt generation.
7.5.2 Interrupt sources
Each peripheral device has one interrupt line connected to the NVIC but may have several
interrupt flags. Individual interrupt flags may also represent more than one interrupt
source.
Any GPIO pin (total of 40 pins) regardless of the selected function, can be programmed to
generate an interrupt on a level, or rising edge or falling edge, or both.
7.6 IOCONFIG block
The IOCONFIG block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on-chip peripherals.
Peripherals should be connected to the appropriate pins prior to being activated and prior
to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is
not mapped to a related pin should be considered undefined.
7.7 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Multiple outputs
can be set or cleared in one write operation.
LPC11C12/C14 use accelerated GPIO functions:
? GPIO registers are a dedicated AHB peripheral so that the fastest possible I/O timing
can be achieved.
? Entire port value can be written in one instruction.
Additionally, any GPIO pin (total of 40 pins) providing a digital function can be
programmed to generate an interrupt on a level, a rising or falling edge, or both.
7.7.1 Features
? Bit level port registers allow a single instruction to set or clear any number of bits in
one write operation.
? Direction control of individual bits.
? All GPIO pins default to inputs with pull-ups enabled after reset except for the I 2 C-bus
true open-drain pins PIO0_4 and PIO0_5.
? Pull-up/pull-down resistor configuration can be programmed through the IOCONFIG
block for each GPIO pin (except PIO0_4 and PIO0_5).
7.8 UART
The LPC11C12/C14 contain one UART.
LPC11C12_C14_0
Preliminary data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 00.05 — 23 April 2010
? NXP B.V. 2010. All rights reserved.
11 of 49
相关PDF资料 |
PDF描述 |
|---|---|
| MCB2470 | BOARD EVAL NXP LPC247X SERIES |
| MCBSTM32EXL | BOARD EVALUATION FOR STM32F103ZE |
| MCBTMPM330 | BOARD EVAL TOSHIBA TMPM330 SER |
| MCIMX25WPDKJ | KIT DEVELOPMENT WINCE IMX25 |
| MCIMX53-START-R | KIT DEVELOPMENT I.MX53 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCB11C14-ED | 制造商:ARM Ltd 功能描述:KEIL NXP LPC11C14 EVAL BOARD |
| MCB11C14U | 功能描述:开发板和工具包 - ARM EVAL BOARD FOR NXP LPC11C14 + ULINK2 RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| MCB11C14UME | 功能描述:开发板和工具包 - ARM EVAL BOARD FOR NXP LPC11C14 + ULINK-ME RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| MCB11C14UME-ED | 制造商:ARM Ltd 功能描述:KEIL NXP LPC11C14 EVAL BOARD |
| MCB11U10 | 功能描述:开发板和工具包 - ARM EVAL BOARD FOR NXP LPC11U14 RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。