- 您现在的位置：买卖IC网 > Datasheet目录342 > MCB11C14 (Keil)BOARD EVAL FOR NXP LPC11C14 Datasheet资料下载
参数资料
| 型号： | MCB11C14 |
| 厂商： | Keil |
| 文件页数： | 40/49页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR NXP LPC11C14 |
| 产品培训模块： | Code Density for LPC11xx |
| 标准包装： | 1 |
| 类型： | MCU |
| 适用于相关产品： | LPC11C14 |
| 所含物品： | 板，线缆 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
NXP Semiconductors
LPC11C12/C14
11. Application information
11.1 ADC usage notes
The following guidelines show how to increase the performance of the ADC in a noisy
? The ADC input trace must be short and as close as possible to the LPC11C12/C14
chip.
? The ADC input traces must be shielded from fast switching digital signals and noisy
power supply lines.
? Because the ADC and the digital core share the same power supply, the power supply
line must be adequately filtered.
? To improve the ADC performance in a very noisy environment, put the device in Sleep
mode during the ADC conversion.
11.2 XTAL input
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
C i = 100 pF. To limit the input voltage to the specified range, choose an additional
capacitor to ground C g which attenuates the input voltage by a factor C i /(C i + C g ). In slave
mode, a minimum of 200 mV(RMS) is needed.
LPC1xxx
XTALIN
Ci
Cg
100 pF
002aae788
Fig 22. Slave mode operation of the on-chip oscillator
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
( Figure 22 ), with an amplitude between 200 mV(RMS) and 1000 mV(RMS). This
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTALOUT pin in this configuration can be left unconnected.
External components and models used in oscillation mode are shown in Figure 23 and in
Table 15 and Table 16 . Since the feedback resistance is integrated on chip, only a crystal
and the capacitances C X1 and C X2 need to be connected externally in case of
fundamental mode oscillation (the fundamental frequency is represented by L, C L and
R S ). Capacitance C P in Figure 23 represents the parallel package capacitance and should
not be larger than 7 pF. Parameters F OSC , C L , R S and C P are supplied by the crystal
LPC11C12_C14_0
Preliminary data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 00.05 — 23 April 2010
? NXP B.V. 2010. All rights reserved.
40 of 49
相关PDF资料 |
PDF描述 |
|---|---|
| MCB2470 | BOARD EVAL NXP LPC247X SERIES |
| MCBSTM32EXL | BOARD EVALUATION FOR STM32F103ZE |
| MCBTMPM330 | BOARD EVAL TOSHIBA TMPM330 SER |
| MCIMX25WPDKJ | KIT DEVELOPMENT WINCE IMX25 |
| MCIMX53-START-R | KIT DEVELOPMENT I.MX53 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCB11C14-ED | 制造商:ARM Ltd 功能描述:KEIL NXP LPC11C14 EVAL BOARD |
| MCB11C14U | 功能描述:开发板和工具包 - ARM EVAL BOARD FOR NXP LPC11C14 + ULINK2 RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| MCB11C14UME | 功能描述:开发板和工具包 - ARM EVAL BOARD FOR NXP LPC11C14 + ULINK-ME RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| MCB11C14UME-ED | 制造商:ARM Ltd 功能描述:KEIL NXP LPC11C14 EVAL BOARD |
| MCB11U10 | 功能描述:开发板和工具包 - ARM EVAL BOARD FOR NXP LPC11U14 RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。