参数资料
型号: MCF5484CVR200
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, 200 MHz, RISC PROCESSOR, PBGA388
封装: 27 X 27 MM, 1 MM PITCH, MS-034AAL-1, PBGA-388
文件页数: 33/34页
文件大小: 602K
代理商: MCF5484CVR200
MCF548x ColdFire Microprocessor, Rev. 4
Hardware Design Considerations
Freescale Semiconductor
8
4.3
General USB Layout Guidelines
4.3.1
USB D+ and D- High-Speed Traces
1. High speed clock and the USBD+ and USBD- differential pair should be routed first.
2. Route USBD+ and USBD- signals on the top layer of the board.
3. The trace width and spacing of the USBD+ and USBD- signals should be such that the differential impedance is 90
Ω.
4. Route traces over continuous planes (power and ground)—they should not pass over any power/ground plane slots or
anti-etch. When placing connectors, make sure the ground plane clear-outs around each pin have ground continuity
between all pins.
5. Maintain the parallelism (skew matched) between USBD+ and USBD-. These traces should be the same overall length.
6. Do not route USBD+ and USBD- traces under oscillators or parallel to clock traces and/or data buses. Minimize the
lengths of high speed signals that run parallel to the USBD+ and USBD- pair. Maintain a minimum 50mil spacing to
clock signals.
7. Keep USBD+ and USBD- traces as short as possible.
8. Route USBD+, USBD-, and USBVBUS signals with a minimum amount of vias and corners. Use 45° turns.
9. Stubs should be avoided as much as possible. If they cannot be avoided, stubs should be no greater than 200mils.
4.3.2
USB VBUS Traces
Connecting the USBVBUS pin directly to the 5V VBUS signal from the USB connector can cause long-term reliability
problems in the ESD network of the processor. Therefore, use of an external voltage divider for VBUS is recommended.
Figure 4 and Figure 5 depict possible connections for VBUS. Point A, marked in each figure, is where a 5V version of VBUS
should connect. Point B, marked in each figure, is where a 3.3V version of VBUS should connect to the USBVBUS pin on the
device.
Figure 4. Preferred VBUS Connections
Figure 5. Alternate VBUS Connections
4.3.3
USB Receptacle Connections
It is recommended to connect the shield and the ground pin of the B USB receptacle for upstream ports to the board ground
plane. The ground pin of the A USB receptacles for downstream ports should also be connected to the board ground plane, but
industry practice varies widely on the connection of the shield of the A USB receptacles to other system grounds. Take
precautions for control of ground loops between hosts and self-powered USB devices through the cable shield.
50k
MCF548x
B
(3.3V)
A
(5V)
8.2k
20k
50k
MCF548x
B
(3.3V)
A
(5V)
50k
相关PDF资料
PDF描述
MCF5481CVR166 32-BIT, 166.66 MHz, RISC PROCESSOR, PBGA388
MCF5483CZP166 32-BIT, 166.66 MHz, RISC PROCESSOR, PBGA388
MCHC805PV8YDWR2 8-BIT, EEPROM, 4.2 MHz, MICROCONTROLLER, PDSO28
MC68HC805PV8YDWR2 8-BIT, EEPROM, 4.2 MHz, MICROCONTROLLER, PDSO28
MC68HC05PV8AYDWR3 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PDSO28
相关代理商/技术参数
参数描述
MCF5484CVR200 制造商:Freescale Semiconductor 功能描述:Microprocessor IC
MCF5484CZP200 功能描述:微处理器 - MPU MCF548X V4ECORE MMU FPU RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MCF5485 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:MCF548x ColdFire㈢ Microprocessor
MCF5485CVR200 功能描述:微处理器 - MPU MCF548X V4ECORE MMU FPU RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MCF5485CZP200 功能描述:微处理器 - MPU MCF548X V4ECORE MMU FPU RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324