- 您现在的位置：买卖IC网 > PDF目录17188 > MCP1631RD-DCPC1 (Microchip Technology)REF DES BATT CHARG OR LED DRIVER PDF资料下载
参数资料
| 型号： | MCP1631RD-DCPC1 |
| 厂商： | Microchip Technology |
| 文件页数： | 28/44页 |
| 文件大小： | 0K |
| 描述： | REF DES BATT CHARG OR LED DRIVER |
| 标准包装： | 1 |
| 电流 - 输出 / 通道： | 700mA |
| 输出及类型： | 1，非隔离 |
| 特点： | 用于锂离子、镍氢和镍镉电池充电器的固件 |
| 输入电压： | 3.5 ~ 16 V |
| 已供物品： | 板 |
| 已用 IC / 零件： | MCP1631HV，PIC16F616 |
| 产品目录页面： | 668 (CN2011-ZH PDF) |
| 相关产品： | MCP1631HV-500E/SS-ND - IC REG CTRLR ISO PWM CM 20-SSOP MCP1631HV-330E/ST-ND - IC REG CTRLR ISO PWM CM 20-TSSOP MCP1631HV-330E/SS-ND - IC REG CTRLR ISO PWM CM 20-SSOP MCP1631HV-500E/ST-ND - IC REG CTRLR ISO PWM CM 20-TSSOP MCP1631HVT-330E/SSTR-ND - IC REG CTRLR ISO PWM CM 20-SSOP MCP1631HVT-500E/SSTR-ND - IC REG CTRLR ISO PWM CM 20-SSOP MCP1631HVT-500E/STTR-ND - IC REG CTRLR ISO PWM CM 20-TSSOP MCP1631HVT-330E/STTR-ND - IC REG CTRLR ISO PWM CM 20-TSSOP PIC16F616T-I/ML-ND - IC PIC MCU FLASH 2KX14 16QFN PIC16F616T-I/ST-ND - IC PIC MCU FLASH 2KX14 14TSSOP 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
PIC16F610/616/16HV610/616
DS41288F-page 34
2009 Microchip Technology Inc.
4.2
Additional Pin Functions
Every PORTA pin on the PIC16F610/616/16HV610/
616 has an interrupt-on-change option and a weak pull-
up option. The next three sections describe these
functions.
4.2.1
ANSEL REGISTER
The ANSEL register is used to configure the Input
mode of an I/O pin to analog. Setting the appropriate
ANSEL bit high will cause all digital reads on the pin to
be read as ‘0’ and allow analog functions on the pin to
operate correctly.
The state of the ANSEL bits has no affect on digital
output functions. A pin with TRIS clear and ANSEL set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
4.2.2
WEAK PULL-UPS
Each of the PORTA pins, except RA3, has an
individually configurable internal weak pull-up. Control
bits WPUAx enable or disable each pull-up. Refer to
Register 4-4. Each weak pull-up is automatically turned
off when the port pin is configured as an output. The
pull-ups are disabled on a Power-on Reset by the
RAPU bit of the OPTION register). A weak pull-up is
automatically enabled for RA3 when configured as
MCLR and disabled when RA3 is an input. There is no
software control of the MCLR pull-up.
4.2.3
INTERRUPT-ON-CHANGE
Each PORTA pin is individually configurable as an
interrupt-on-change pin. Control bits IOCAx enable or
disable the interrupt function for each pin. Refer to
Register 4-5. The interrupt-on-change is disabled on a
Power-on Reset.
For enabled interrupt-on-change pins, the values are
compared with the old value latched on the last read of
PORTA. The ‘mismatch’ outputs of the last read are
OR’d together to set the PORTA Change Interrupt Flag
bit (RAIF) in the INTCON register (Register 2-3).
This interrupt can wake the device from Sleep. The
user, in the Interrupt Service Routine, clears the
interrupt by:
a)
Any read or write of PORTA. This will end the
mismatch condition, then,
b)
Clear the flag bit RAIF.
A mismatch condition will continue to set flag bit RAIF.
Reading PORTA will end the mismatch condition and
allow flag bit RAIF to be cleared. The latch holding the
last read value is not affected by a MCLR nor BOR
Reset. After these resets, the RAIF flag will continue to
be set if a mismatch is present.
Note:
If a change on the I/O pin should occur
when any PORTA operation is being
executed, then the RAIF interrupt flag may
not get set.
REGISTER 4-3:
ANSEL: ANALOG SELECT REGISTER
R/W-1
ANS7
ANS6
ANS5
ANS4
ANS3(2)
ANS2(2)
ANS1
ANS0
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-0
ANS<7:0>: Analog Select bits
Analog select between analog or digital function on pins AN<7:0>, respectively.
1
= Analog input. Pin is assigned as analog input(1).
0
= Digital I/O. Pin is assigned to port or special function.
Note 1:
Setting a pin to an analog input automatically disables the digital input circuitry, weak pull-ups, and
interrupt-on-change if available. The corresponding TRIS bit must be set to Input mode in order to allow
external control of the voltage on the pin.
2:
PIC16F616/HV616.
相关PDF资料 |
PDF描述 |
|---|---|
| GEC30DRXN | CONN EDGECARD 60POS DIP .100 SLD |
| TC4467CPD | IC MOSFET DVR QUAD NAND 14DIP |
| TC1411VUA713 | IC MOSFET DVR 1A HS INV 8MSOP |
| R1D-1209/P | CONV DC/DC 1W 12VIN +/-09VOUT |
| T95S335K016CZAL | CAP TANT 3.3UF 16V 10% 1507 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1631RD-MCC1 | 功能描述:电源管理IC开发工具 MCP1631HV Multi-Chem Chrgr Ref Design RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MCP1631RD-MCC2 | 功能描述:开关变换器、稳压器与控制器 MCP1631HV Multi-Chem BuckBst Chg Ref Dsgn RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCP1631T | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
| MCP1631T-330E/ML | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
| MCP1631T-330E/SS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
发布紧急采购，3分钟左右您将得到回复。