- 您现在的位置：买卖IC网 > PDF目录1852 > MCP1640C-I/MC (Microchip Technology)IC REG BOOST SYNC ADJ 0.1A 8DFN PDF资料下载
参数资料
| 型号： | MCP1640C-I/MC |
| 厂商： | Microchip Technology |
| 文件页数： | 13/32页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 0.1A 8DFN |
| 特色产品： | MCP1640 Boost Regulator |
| 标准包装： | 150 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2 V ~ 5.5 V |
| 输入电压： | 0.8 V ~ 5.5 V |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 100mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 8-DFN（3x2） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
MCP1640/B/C/D
4.2.2
PWM-ONLY MODE OPERATION
4.2.6
INTERNAL BIAS
In normal PWM operation, the MCP1640/B/C/D
operates as a fixed frequency, synchronous boost
converter. The switching frequency is internally
maintained with a precision oscillator typically set to
500 kHz. The MCP1640B/D devices will operate in
PWM-Only mode even during periods of light load
operation. By operating in PWM-Only mode, the output
ripple remains low and the frequency is constant.
Operating in fixed PWM mode results in lower
The MCP1640/B/C/D gets its start-up bias from V IN .
Once the output exceeds the input, bias comes from
the output. Therefore, once started, operation is
completely independent of V IN . Operation is only
limited by the output power level and the input source
series resistance. When started, the output will remain
in regulation down to 0.35V typical with 1 mA output
current for low source impedance inputs.
efficiency during light load operation (when compared
4.2.7
INTERNAL COMPENSATION
to PFM mode (MCP1640C)).
Lossless current sensing converts the peak current sig-
nal to a voltage to sum with the internal slope compen-
sation. This summed signal is compared to the voltage
error amplifier output to provide a peak current control
command for the PWM signal. The slope
compensation is adaptive to the input and output
voltage. Therefore, the converter provides the proper
amount of slope compensation to ensure stability, but is
not excessive, which causes a loss of phase margin.
The error amplifier, with its associated compensation
network, completes the closed loop system by
comparing the output voltage to a reference at the
input of the error amplifier, and feeding the amplified
and inverted signal to the control input of the inner
current loop. The compensation network provides
phase leads and lags at appropriate frequencies to
cancel excessive phase lags and leads of the power
circuit. All necessary compensation components and
slope compensation are integrated.
The peak current limit is set to 800 mA typical.
4.2.8
SHORT CIRCUIT PROTECTION
4.2.3
PFM MODE OPERATION
Unlike most boost converters, the MCP1640/B/C/D
The MCP1640C devices are capable of operating in
normal PWM mode and PFM mode to maintain high
efficiency at all loads. In PFM mode, the output ripple
has a variable frequency component that changes with
the input voltage and output current. With no load, the
quiescent current draw from the output is typically
19 μA. The PFM mode can be disabled in selected
allows its output to be shorted during normal operation.
The internal current limit, and overtemperature
protection, limit excessive stress and protect the device
during periods of short circuit, overcurrent and over-
temperature. While operating in Bypass mode, the
P-Channel current limit is inhibited to minimize
quiescent current.
device options.
PFM operation is initiated if the output load current falls
4.2.9
LOW NOISE OPERATION
below an internally programmed threshold. The output
voltage is continuously monitored. When the output
voltage drops below its nominal value, PFM operation
pulses one or several times to bring the output back
into regulation. If the output load current rises above
The MCP1640/B/C/D integrates a low noise anti-ring
switch that damps the oscillations typically observed at
the switch node of a boost converter when operating in
the Discontinuous Inductor Current mode. This
removes the high frequency radiated noise.
the upper threshold, the MCP1640C transitions
smoothly into PWM mode.
4.2.10
OVERTEMPERATURE
PROTECTION
4.2.4
ADJUSTABLE OUTPUT VOLTAGE
Overtemperature protection circuitry is integrated into
The MCP1640/B/C/D output voltage is adjustable with
a resistor divider over a 2.0V minimum to 5.5V
maximum range. High value resistors are
recommended to minimize quiescent current to keep
efficiency high at light loads.
the MCP1640/B/C/D. This circuitry monitors the device
junction temperature and shuts the device off if the
junction temperature exceeds the typical +150 o C
threshold. If this threshold is exceeded, the device will
automatically restart when the junction temperature
drops by 10 o C. The soft start is reset during an
4.2.5
ENABLE PIN
overtemperature condition.
The enable pin is used to turn the boost converter on
and off. The enable threshold voltage varies with input
voltage. To enable the boost converter, the EN voltage
level must be greater than 90% of the V IN voltage. To
disable the boost converter, the EN voltage must be
less than 20% of the V IN voltage.
? 2011 Microchip Technology Inc.
DS22234B-page 13
相关PDF资料 |
PDF描述 |
|---|---|
| MCP1653ST-E/UN | IC REG CTRLR BST FLYBK CM 10MSOP |
| MCP1700-3002E/TO | IC REG LDO 3V .25A TO-92-3 |
| MCP1701AT-4602I/MB | IC REG LDO 4.6V SOT89-3 |
| MCP1702T-1502E/MB | IC REG LDO 1.5V 50MA SOT89-3 |
| MCP1703AT-5002E/DB | IC REG LDO 5V .25A SOT-223-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1640CT-I/CH | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:0.65V Start-up Synchronous Boost Regulator with True Output Disconnect or Input/Output Bypass Option |
| MCP1640CT-I/CHY | 功能描述:直流/直流开关转换器 500 kHz 300 mA Syn Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MCP1640CT-I/MC | 功能描述:直流/直流开关转换器 500 kHz 300 mA Syn Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MCP1640D | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:0.65V Start-up Synchronous Boost Regulator with True Output Disconnect or Input/Output Bypass Option |
| MCP1640DCT-ICH | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:0.65V START-UP SYNCHRONOUS BOOST REGULATOR WITH TRUE OUTPUT DISCONNECT OR INPUT/OUTPUT BYPASS OPTION |
发布紧急采购，3分钟左右您将得到回复。