- 您现在的位置：买卖IC网 > PDF目录1852 > MCP1640C-I/MC (Microchip Technology)IC REG BOOST SYNC ADJ 0.1A 8DFN PDF资料下载
参数资料
| 型号： | MCP1640C-I/MC |
| 厂商： | Microchip Technology |
| 文件页数： | 9/32页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 0.1A 8DFN |
| 特色产品： | MCP1640 Boost Regulator |
| 标准包装： | 150 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2 V ~ 5.5 V |
| 输入电压： | 0.8 V ~ 5.5 V |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 100mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 8-DFN（3x2） |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
MCP1640/B/C/D
3.0
PIN DESCRIPTIONS
TABLE 3-1:
PIN FUNCTION TABLE
Pin
Name
MCP1640/B/C/D MCP1640/B/C/D
SOT23 2x3 DFN
Description
SW
GND
EN
FB
V OUT
V IN
S GND
P GND
V OUTS
V OUTP
EP
1
2
3
4
5
6
—
—
—
—
—
5
—
4
1
—
8
2
3
7
6
9
Switch Node, Boost Inductor Input Pin
Ground Pin
Enable Control Input Pin
Feedback Voltage Pin
Output Voltage Pin
Input Voltage Pin
Signal Ground Pin
Power Ground Pin
Output Voltage Sense Pin
Output Voltage Power Pin
Exposed Thermal Pad (EP); must be connected to V SS.
3.1
Switch Node Pin (SW)
3.6
Power Supply Input Voltage Pin
Connect the inductor from the input voltage to the SW
pin. The SW pin carries inductor current and can be as
high as 800 mA peak. The integrated N-Channel switch
drain and integrated P-Channel switch source are inter-
(V IN )
Connect the input voltage source to V IN . The input
source should be decoupled to GND with a 4.7 μF
minimum capacitor.
nally connected at the SW node.
3.7
Signal Ground Pin (S GND )
3.2
Ground Pin (GND)
The signal ground pin is used as a return for the
The ground or return pin is used for circuit ground con-
nection. Length of trace from input cap return, output
cap return, and GND pin should be made as short as
integrated V REF and error amplifier. In the 2x3 DFN
package, the S GND and power ground (P GND ) pins are
connected externally.
possible to minimize noise on the GND pin. In the
3.8
Power Ground Pin (P GND )
SOT23-6 package, a single ground pin is used.
The power ground pin is used as a return for the high-
3.3
Enable Pin (EN)
current N-Channel switch. In the 2x3 DFN package, the
P GND and S GND pins are connected externally.
The EN pin is a logic-level input used to enable or
disable device switching, and lower quiescent current
while disabled. A logic high (>90% of V IN ) will enable
the regulator output. A logic low (<20% of V IN ) will
ensure that the regulator is disabled.
3.9 Output Voltage Sense Pin (V OUTS )
The output voltage sense pin connects the regulated
output voltage to the internal bias circuits. In the 2x3
DFN package, the V OUTS and output voltage power
(V OUTP ) pins are connected externally.
3.4
Feedback Voltage Pin (FB)
3.10
Output Voltage Power Pin (V OUTP )
The FB pin is used to provide output voltage regulation
by using a resistor divider. The FB voltage will be 1.21V
typical with the output voltage in regulation.
3.5 Output Voltage Pin (V OUT )
The output voltage pin connects the integrated
P-Channel MOSFET to the output capacitor. The FB
voltage divider is also connected to the V OUT pin for
voltage regulation.
? 2011 Microchip Technology Inc.
The output voltage power pin connects the output volt-
age to the switch node. High current flows through the
integrated P-Channel and out of this pin to the output
capacitor and output. In the 2x3 DFN package, V OUTP
and V OUTS are connected externally.
3.11 Exposed Thermal Pad (EP)
There is no internal electrical connection between the
Exposed Thermal Pad (EP) and the S GND and P GND
pins. They must be connected to the same potential on
the Printed Circuit Board (PCB).
DS22234B-page 9
相关PDF资料 |
PDF描述 |
|---|---|
| MCP1653ST-E/UN | IC REG CTRLR BST FLYBK CM 10MSOP |
| MCP1700-3002E/TO | IC REG LDO 3V .25A TO-92-3 |
| MCP1701AT-4602I/MB | IC REG LDO 4.6V SOT89-3 |
| MCP1702T-1502E/MB | IC REG LDO 1.5V 50MA SOT89-3 |
| MCP1703AT-5002E/DB | IC REG LDO 5V .25A SOT-223-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1640CT-I/CH | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:0.65V Start-up Synchronous Boost Regulator with True Output Disconnect or Input/Output Bypass Option |
| MCP1640CT-I/CHY | 功能描述:直流/直流开关转换器 500 kHz 300 mA Syn Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MCP1640CT-I/MC | 功能描述:直流/直流开关转换器 500 kHz 300 mA Syn Boost Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MCP1640D | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:0.65V Start-up Synchronous Boost Regulator with True Output Disconnect or Input/Output Bypass Option |
| MCP1640DCT-ICH | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:0.65V START-UP SYNCHRONOUS BOOST REGULATOR WITH TRUE OUTPUT DISCONNECT OR INPUT/OUTPUT BYPASS OPTION |
发布紧急采购，3分钟左右您将得到回复。