- 您现在的位置：买卖IC网 > PDF目录17178 > MCP1650DM-LED1 (Microchip Technology)BOARD DEMO FOR MCP165X PDF资料下载
参数资料
| 型号： | MCP1650DM-LED1 |
| 厂商： | Microchip Technology |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO FOR MCP165X |
| 标准包装： | 1 |
| 输出及类型： | 1，非隔离 |
| 特点： | 可调光 |
| 输入电压： | 2 ~ 4.5 V |
| 已供物品： | 板 |
| 已用 IC / 零件： | MCP1651 |
| 相关产品： | MCP1653ST-E/UN-ND - IC REG CTRLR BST FLYBK CM 10MSOP MCP1653S-E/UN-ND - IC REG CTRLR BST FLYBK CM 10MSOP MCP1653RT-E/UN-ND - IC REG CTRLR BST FLYBK CM 10MSOP MCP1653R-E/UN-ND - IC REG CTRLR BST FLYBK CM 10MSOP MCP1652ST-E/MS-ND - IC REG CTRLR BST FLYBK PWM 8MSOP MCP1652S-E/MS-ND - IC REG CTRLR BST FLYBK PWM 8MSOP MCP1652RT-E/MS-ND - IC REG CTRLR BST FLYBK PWM 8MSOP MCP1652R-E/MS-ND - IC REG CTRLR BST FLYBK PWM 8MSOP MCP1651ST-E/MS-ND - IC REG CTRLR BST FLYBK PWM 8MSOP MCP1651S-E/MS-ND - IC REG CTRLR BST FLYBK PWM 8MSOP 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MCP1650/51/52/53
5.2
Design Considerations
5.2.1.1
Calculations
When developing switching power converter circuits,
there are numerous things to consider and the
MCP1650/51/52/53 family is no exception. The gated
oscillator architecture does provide a simple control
approach so that stabilizing the regulator output is an
easier task than that of a fixed-frequency regulator.
The MCP1650/51/52/53 controller utilizes an external
switch and diode allowing for a very wide range of
conversion (high voltage gain and/or high current gain).
There are practical, as well as power-conversion,
topology limitations. The MCP1650/51/52/53 gated
oscillator hysteretic mode converter has similar
limitations, as do fixed-frequency boost converters.
P OUT = V O UT × I OU T
Where:
P OUT = 12V X 100 mA
P OUT = 1.2 Watts
P IN = P OU T ? ( Efficiency )
Where:
P IN = 1.2W/80%
(80% is a good efficiency estimate)
P IN = 1.5 Watts
For gated oscillator hysteretic designs, the switching
5.2.1
DESIGN EXAMPLE
Input Voltage = 2.8V to 4.2V
frequency is not constant and will gate several pulses
to raise the output voltage. Once the upper hysteresis
threshold is reached, the gated pulses stop and the
V O UT = ? ------------- ? × V IN
R TO P = R BO T × ? ? ? ? ? ? – 1 ? ?
V OU T
V OUTMAX = ? ? ? ? × 2.8
----------------
V OU TMAX = ? ------------------- ? × 3.8
Output Voltage = 12V
Output Current = 100 mA
Oscillator Frequency = 750 kHz
Duty cycle = 80% for V IN < 3.8V
Duty cycle = 56% for V IN > 3.8V
Setting the output voltage:
-------------
V FB
Where:
R TOP = Top Resistor Value
R BOT = Bottom Resistor Value
By adjusting the external resistor divider, the output
voltage of the boost converter can be set to the desired
value. Due to the RC delay caused by the resistor
divider and the device input capacitance, resistor
values greater than 100 k ? are not recommended. The
feedback voltage is typically 1.22V.
For this example:
R BOT = 10 k ?
V OUT = 12V
V FB = 1.22V
R TOP = 88.4 k ?
90.9 K ? was selected as the closest standard value.
? 2004 Microchip Technology Inc.
output will coast down at a rate determined by the out-
put capacitor and the load. Using the gated oscillator
switching frequency and duty cycle, it is possible to
determine what the maximum boost ratio is for
continuous inductor current operation.
1
? 1 – D ?
This relationship assumes that the output load current
is significant and the boost converter is operating in
Continuous Inductor Current mode. If the load is very
light or a small boost inductance is used, higher boost
ratio’s can be achieved.
Calculate at minimum V IN :
1
1 – 0.8
The ideal maximum output voltage is 14V. The actual
measured result will be less due to the forward voltage
drop in the boost diode, as well as other circuit losses.
For applications where the input voltage is above and
below 3.8V, another point must be checked to deter-
mine the maximum boost ratio. At 3.8V, the duty cycle
changes from 80% to 56% to minimize the peak current
in the inductor.
1
? 1 – 0.56 ?
For this case, V OUTMAX = 8.63V less than the required
12V output specified. The size of the inductor has to
decrease in order to operate the boost regulator in
Discontinuous Inductor Current mode.
DS21876A-page 17
相关PDF资料 |
PDF描述 |
|---|---|
| TC4425EMF713 | IC MOSFET DVR 3A DUAL HS 8DFN |
| R0.25S-0524/P-R | CONV DC/DC 0.25W 5V IN 24V OUT |
| LB2012T1R0M | INDUCTOR WOUND 1.0UH 405MA 0805 |
| EBM12DRMH-S288 | CONN EDGECARD 24POS .156 EXTEND |
| T95S475K010HZSL | CAP TANT 4.7UF 10V 10% 1507 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1650DM-LED2 | 功能描述:电源管理IC开发工具 MCP1650 Mult Wht LED Demo Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MCP1650EV | 功能描述:开发板和工具包 - PIC / DSPIC MCP1650 Boost Contr Eval Board RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: |
| MCP1650R-E/MS | 功能描述:直流/直流开关转换器 UVLO 2V RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MCP1650R-E/MS | 制造商:Microchip Technology Inc 功能描述:Controller IC |
| MCP1650REMS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:750 kHz Boost Controller |
发布紧急采购，3分钟左右您将得到回复。