- 您现在的位置：买卖IC网 > PDF目录13408 > MCP1727-2502E/MF (Microchip Technology)IC REG LDO 2.5V 1.5A 8DFN PDF资料下载
参数资料
| 型号： | MCP1727-2502E/MF |
| 厂商： | Microchip Technology |
| 文件页数： | 18/32页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.5V 1.5A 8DFN |
| 产品培训模块： | High Current LDOs |
| 标准包装： | 120 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.5V |
| 输入电压： | 最高 6V |
| 电压 - 压降（标准）： | 0.33V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 管件 |
| 产品目录页面： | 665 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
MCP1727
Once the power good threshold (rising) has been
reached, the C DELAY pin charges the external capacitor
to V IN . The charging current is 140 nA (typical). The
PWRGD output will transition high when the C DELAY pin
voltage has charged to 0.42V. If the output falls below
the power good threshold limit during the charging time
between 0.0V and 0.42V on the C DELAY pin, the
C DELAY pin voltage will be pulled to ground, thus reset-
ting the timer. The C DELAY pin will be held low until the
output voltage of the LDO has once again risen above
high (turn-on) to the LDO output being in regulation is
typically 100 μs. See Figure 4-5 for a timing diagram of
the SHDN input.
T OR
400 ns (typ)
70 μs
30 μs
SHDN
the power good rising threshold. A timing diagram
showing C DELAY , PWRGD and V OUT is shown in
V OUT
V OUT
V PWRGD_TH
FIGURE 4-5:
Diagram.
Shutdown Input Timing
T PG
C DELAY
V IN (typ)
4.8
Dropout Voltage and Undervoltage
0V
PWRGD
FIGURE 4-4:
Diagram.
C DELAY Threshold (0.42V)
C DELAY and PWRGD Timing
Lockout
Dropout voltage is defined as the input-to-output
voltage differential at which the output voltage drops
2% below the nominal value that was measured with a
V R + 0.6V differential applied. The MCP1727 LDO has
a very low dropout voltage specification of 330 mV
“Electrical Characteristics” for maximum dropout
voltage specifications.
The MCP1727 LDO operates across an input voltage
4.7
Shutdown Input (SHDN)
range of 2.3V to 6.0V and incorporates input Undervolt-
age Lockout (UVLO) circuitry that keeps the LDO
The SHDN input is an active-low input signal that turns
the LDO on and off. The SHDN threshold is a
percentage of the input voltage. The typical value of
this shutdown threshold is 30% of V IN , with minimum
and maximum limits over the entire operating
temperature range of 45% and 15%, respectively.
The SHDN input will ignore low-going pulses (pulses
meant to shut down the LDO) that are up to 400 ns in
pulse width. If the shutdown input is pulled low for more
than 400 ns, the LDO will enter Shutdown mode. This
small bit of filtering helps to reject any system noise
spikes on the shutdown input signal.
On the rising edge of the SHDN input, the shutdown
circuitry has a 30 μs delay before allowing the LDO
output to turn on. This delay helps to reject any false
turn-on signals or noise on the SHDN input signal. After
the 30 μs delay, the LDO output enters its soft-start
period as it rises from 0V to its final regulation value. If
the SHDN input signal is pulled low during the 30 μs
delay period, the timer will be reset and the delay time
will start over again on the next rising edge of the
SHDN input. The total time from the SHDN input going
DS21999B-page 18
output voltage off until the input voltage reaches a
minimum of 2.18V (typical) on the rising edge of the
input voltage. As the input voltage falls, the LDO output
will remain on until the input voltage level reaches
2.04V (typical).
Since the MCP1727 LDO undervoltage lockout
activates at 2.04V as the input voltage is falling, the
dropout voltage specification does not apply for output
voltages that are less than 1.9V.
For high-current applications, voltage drops across the
PCB traces must be taken into account. The trace
resistances can cause significant voltage drops
between the input voltage source and the LDO. For
applications with input voltages near 2.3V, these PCB
trace voltage drops can sometimes lower the input
voltage enough to trigger a shutdown due to
undervoltage lockout.
? 2007 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| 10ZLJ4700MG412.5X30 | CAP ALUM 4700UF 10V 20% RADIAL |
| MAX706CUA+T | IC SUPERVISOR MPU 8-UMAX |
| MCP1825S-3002E/EB | IC REG LDO 3V .5A 3DDPAK |
| V24B8C200BG | CONVERTER MOD DC/DC 8V 200W |
| MCP1825S-3302E/AB | IC REG LDO 3.3V .5A TO220-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1727-3002E/MF | 功能描述:低压差稳压器 - LDO 1.5A CMOS LDO 3.0V DFN8 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1727-3002E/SN | 功能描述:低压差稳压器 - LDO 1.5A CMOS LDO 3.0V SOIC8 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1727-3302E/MF | 功能描述:低压差稳压器 - LDO 1.5A CMOS LDO 3.3V DFN8 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1727-3302E/SN | 功能描述:低压差稳压器 - LDO 1.5A Vout=3.3V Extended Temp RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MCP1727-5002E/MF | 功能描述:低压差稳压器 - LDO 1.5A CMOS LDO 5.0V DFN8 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。