- 您现在的位置：买卖IC网 > PDF目录10975 > MCP2122-E/SN (Microchip Technology)IC ENCODER/DECODER IRDA 8SOIC PDF资料下载
参数资料
| 型号： | MCP2122-E/SN |
| 厂商： | Microchip Technology |
| 文件页数： | 3/38页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER/DECODER IRDA 8SOIC |
| 标准包装： | 100 |
| 类型： | 红外线编码器/解码器 |
| 应用： | 数据记录，数据交换 |
| 电压 - 电源，模拟： | 1.8 V ~ 5.5 V |
| 电压 - 电源，数字： | 1.8 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
| 产品目录页面： | 684 (CN2011-ZH PDF) |
| 配用： | MCP212XDM-ND - BOARD DEVELOPMENT IRDA |
| 其它名称： | MCP2122-E/SNG MCP2122-E/SNG-ND |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
2007 Microchip Technology Inc.
Preliminary
DS21894C-page 11
MCP2122
2.6
Host UART Interface
The UART interface is used to communicate with the
Host Controller. Though a UART is capable of a full-
duplex interface, the direct coupling to the IR encoder/
decoder allows only half-duplex operation (since the IR
side is either receiving or transmitting and not both at
the same time). This means that the system can’t
transmit and receive at the same time.
2.6.1
TRANSMITTING
When the controller sends serial data to the MCP2122,
the baud rates are required to match.
There will be some jitter on the detection of the high-to-
low edge of the start bit. This jitter will affect the place-
ment of the encoded start bit. All subsequent bits will be
16 BITCLK times later.
While RXIR is receiving data (low pulse), the TXIR pin
is disabled from transmitting.
2.6.2
RECEIVING
When the controller receives serial data from the
MCP2122, the baud rates are required to match.
There will be some jitter on the detection of the high-to-
low edge of the Start bit. This jitter will affect the
placement of the decoded Start bit. All subsequent bits
will be 16 BITCLK times later.
The TXIR pin is disabled when data is being received
(low pulse) on the RXIR pin.
2.7
IR Interface
The IR interface is used to communicate with the
optical receiver circuitry. The IR interface is either
transmitting data or receiving data (half-duplex).
2.8
Encoding/Decoding Jitter and
Offset
Figure 2-11 shows the jitter on the RXIR and TX pins,
along with the offset on the RX pin and the TXIR pin.
Jitter is the possible variation of the desired edge.
Figure 2-9 and Figure 2-10 show the jitter of the TX pin
(range is indicated by red dashed lines).
Offset is the propagation delay of the input signal (RXIR
or TX) to the output signal (RX or TXIR). Figure 2-9 and
Figure 2-10 show the offset of the TXIR pin from the
16XCLK signal that starts the bit time.
2.9
Minimizing Power
The device can be placed in a low-power mode by
forcing the RESET pin low. This disables the internal
state machine. To ensure that the lowest power
consumption is obtained, ensure that the 16XCLK pin
is not active and that the other input pins (TX and RXIR)
are at a logic-high or logic-low level.
2.9.1
RETURNING TO OPERATION
When returning to normal operation, the RESET pin
must be forced high and the 16XCLK signal should be
operating. Time should be given to ensure that the
16XCLK is stabilized at the desired frequency before
data is allowed to be transmitted or received.
FIGURE 2-11:
EFFECTS OF JITTER AND OFFSET
TX Jitter
3 16XCLK
BITCLK
RXIR
RX
TX
TXIR
16 16XCLK
3 16XCLK
16 16XCLK
RX Jitter
TX Offset
RX Offset
16 16XCLK
相关PDF资料 |
PDF描述 |
|---|---|
| VE-22H-IY-F2 | CONVERTER MOD DC/DC 52V 50W |
| MCP2122T-E/SN | IC ENCODER/DECODER IRDA 8SOIC |
| JN1AS10UL1 | CONN RCPT WATERPRF 10POS T/H PIN |
| VE-224-IY-F1 | CONVERTER MOD DC/DC 48V 50W |
| S9S08DZ96F2MLH | MCU 96K FLASH MASK AUTO 64-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2122T-E/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Infrared Encoder/Decoder |
| MCP2122T-E/SN | 功能描述:编码器、解码器、复用器和解复用器 IrDA Encoder/Decoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| MCP2122T-E/SNG | 功能描述:编码器、解码器、复用器和解复用器 Extended Temp Range (-40 to 125C) RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| MCP212XDM | 功能描述:其他开发工具 MCP2120/22 Dev Board RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压: |
| MCP212XEV-DB | 功能描述:子卡和OEM板 MCP212X Dev Dghtr Brd RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
发布紧急采购，3分钟左右您将得到回复。