参数资料
型号: MCP2140-I/SO
厂商: Microchip Technology
文件页数: 6/58页
文件大小: 0K
描述: IC IRDA CONTROLLR DTE/DCE 18SOIC
产品培训模块: IrDA® Standard Protocol
标准包装: 42
控制器类型: IRDA 标准协议栈控制器
接口: UART
电源电压: 3 V ~ 5.5 V
电流 - 电源: 2.2mA
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 18-SOIC(0.295",7.50mm 宽)
供应商设备封装: 18-SOIC
包装: 管件
产品目录页面: 685 (CN2011-ZH PDF)
配用: MCP2140DM-TMPSNS-ND - BOARD DEMO FOR MCP2140
MCP2140
DS21790A-page 14
Preliminary
2003 Microchip Technology Inc.
2.8
Minimizing Power
During IR communication between a Primary Device
and the MCP2140, the MCP2140 is in an operational
mode. In this mode, the MCP2140 consumes the
operational current (Parameter D010).
For many applications, the time that IR communication
is occurring is a small percentage of the applications
operational time. The ability for the IR controller to be
in a low power mode during this time will save on the
applications power consumption. The MCP2140 will
automatically enter a low power mode once IR activity
has stopped and will return to operational mode once
IR activity is detected on the RXPD and RXPDREF
pins.
Another way to minimize system power is to use an I/O
pin of the Host Controller to enable power to the IR
circuity
2.8.1
AUTOMATIC LOW POWER MODE
The Automatic Low Power mode allows the system to
achieve the lowest possible operating current.
When the IR link has been “closed”, the protocol han-
dler state machine returns to the Normal Disconnect
Mode (NDM). During NDM, if no IR activity occurs for
about 10 seconds, the device is disabled and enters
into Low Power mode. In this mode, the device oscilla-
tor is shut down and the PHACT pin will be low
Table 2-3 shows the MCP2140 current. These are
TABLE 2-3:
DEVICE MAXIMUM
OPERATING CURRENT
2.8.2
RETURNING TO DEVICE
OPERATION
The device will exit the Low Power mode when the
RXPD pin voltage crosses the REPDREF pin reference
voltage.
A device reset will also cause the MCP2140 to exit Low
Power mode. After device initialization, if no IR activity
occurs for about 10 seconds, the device is disabled and
returns into the Low Power mode.
2.9
PHACT Signal
The PHACT signal indicates that the MCP2140 Proto-
col Handler is active. This output pin is an open collec-
tor, so when interfacing to the Host Controller, a pull-up
resistor is required.
Mode
Current
Comment
PHACT = H 2.2 mA IR communications is
occurring.
PHACT = L
60 A
No IR communications.
Note:
Additional system current is from the
Receiver/Transmitter circuitry.
Note:
For proper operation, the device oscillator
must be within oscillator specification in
the
time
frame
specified
in
相关PDF资料
PDF描述
ENC28J60T-I/SO IC ETHERNET CTRLR W/SPI 28-SOIC
ENC28J60T-I/SS IC ETHERNET CTLR SPI 28SSOP
GRM21BF51C225ZA01K CAP CER 2.2UF 16V Y5V 0805
GRM21BF51A225ZA01K CAP CER 2.2UF 10V Y5V 0805
MCP2140A-I/SS IC IRDA CONTROLLR DTE/DCE 20SSOP
相关代理商/技术参数
参数描述
MCP2140-ISS 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:IrDA㈢ Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate
MCP2140T-I/SO 功能描述:网络控制器与处理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MCP2140T-I/SS 功能描述:网络控制器与处理器 IC 9600bd fixd spd IrDA RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MCP2140T-IP 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:IrDA㈢ Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate
MCP2140T-ISO 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:IrDA㈢ Standard Protocol Stack Controller With Fixed 9600 Baud Communication Rate