- 您现在的位置：买卖IC网 > PDF目录11581 > MCP2150T-I/SS (Microchip Technology)IC IRDA STD CONTROLLER 20SSOP PDF资料下载
参数资料
| 型号： | MCP2150T-I/SS |
| 厂商： | Microchip Technology |
| 文件页数： | 11/52页 |
| 文件大小： | 0K |
| 描述： | IC IRDA STD CONTROLLER 20SSOP |
| 标准包装： | 1,600 |
| 控制器类型： | IRDA 标准协议栈控制器 |
| 接口： | UART |
| 电源电压： | 3 V ~ 5.5 V |
| 电流 - 电源： | 7mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
| 配用： | MCP215XDM-ND - BOARD DEMO FOR MCP215X |
| 其它名称： | MCP2150TI/SS |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
2002 Microchip Technology Inc.
Preliminary
DS21655B-page 19
MCP2150
2.11
Turnaround Latency
An IR link can be compared to a one-wire data connec-
tion. The IR transceiver can transmit or receive, but not
both at the same time. A delay of one bit time is recom-
mended between the time a byte is received and
another byte is transmitted.
2.12
IR Port Baud Rate
The baud rate for the MCP2150 IR port (the TXIR and
RXIR pins) is, initially, at the default rate of 9600 baud.
The Primary device determines the maximum baud
rate that the MCP2150 will operate at. This information
is used during NDM, with the Primary device setting the
baud rate of the IR link. The maximum IR baud rate is
not required to be the same as the MCP2150’s serial
port (UART) baud rate (as determined by the
BAUD1:BAUD0 pins).
2.13
Programmable Device ID
The MCP2150 has a flexible feature that allows the
MCP2150 Device ID to be changed by the Host Con-
troller. The default ID is “Generic IrDA” and is stored in
non-volatile, electrically erasable programmable mem-
ory (EEPROM). The maximum ID String length is 19
bytes. The format of the ID EEPROM is shown in
The ID String must only contain the ASCII characters
from 20h to 7Ah (inclusive).
The MCP2150 enters into ID String programming when
it exits the reset state and detects that the DTR pin is
high and the RTS pin is low.
A Host Controller connected to the MCP2150 would,
typically, perform the following steps to place the
MCP2150 into ID String programming mode:
1.
Force the MCP2150 into reset (RESET pin
forced low).
2.
Force the DTR pin high and the RTS pin low.
3.
Release the MCP2150 from reset (RESET pin
forced high).
4.
Wait for device to complete initialization.
TABLE 2-5:
DTR/RTS STATE & DEVICE
MODE
Once the MCP2150 is ready to receive data, the CTS
pin will be forced low. Data may now be transferred, fol-
lowing the format in Figure 2-11. The CTS pin deter-
mines the flow control and the Host Controller must
monitor this signal to ensure that the data byte may be
sent.
Once the Host Controller has sent its last byte, the DTR
pin must be set low. This ensures that, if another reset
occurs, the MCP2150 will not reenter ID String pro-
gramming mode. The MCP2150 uses the String Length
(1st byte transmitted) to determine when the ID String
programming mode has completed. This returns the
MCP2150 to normal operation.
Example 2-1 shows the firmware code for a
PIC16CXXX acting as the Host Controller to modify the
MCP2150 Device ID String.
FIGURE 2-11:
ID STRING FORMAT
DTR
RTS
After Device Reset *
0X
Enter Normal Mode
10
Enter Programmable Device ID
11
Enter Normal Mode
* Until device initialization is complete.
Note 1: If a non-valid ID String (containing an ASCII
character not in the valid range) is
programmed, the MCP2150 will not create
a link with a Primary device.
2: The communication program supplied with
Microsoft’s Windows operating system
(called HyperTerminal) may leave the DTR
signal high and the RTS signals low when
the program disconnects, or is closed. Care
should be taken to ensure that this does not
accidently cause the MCP2150 to enter
Device ID String Programming.
Length
ID String
1 Byte
1 to 19 Bytes
1st Byte
Transferred
Last Byte
Transferred
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2155T-I/SO | IC IRDA PROTOCOL CONTRLR 18-SOIC |
| PIC18F25J10T-I/SS | IC PIC MCU FLASH 16KX16 28SSOP |
| PIC16LC54C-04/SO | IC MCU OTP 512X12 18SOIC |
| PIC16LC54C-04I/SO | IC MCU OTP 512X12 18SOIC |
| MCP2155T-I/SS | IC IRDA PROTOCOL CONTRLR 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2155 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Infrared Encoder/Decoder |
| MCP2155_13 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:IrDA?? Standard Protocol Stack Controller |
| MCP2155-I/P | 功能描述:网络控制器与处理器 IC IrDA protocol handlr RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCP2155-I/P | 制造商:Microchip Technology Inc 功能描述:Infrared Encoder/Decoder IC |
| MCP2155-I/SO | 功能描述:网络控制器与处理器 IC IrDA protocol handlr RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。