- 您现在的位置：买卖IC网 > PDF目录11780 > MCP2210T-I/SO (Microchip Technology)IC CONVERTER USB-PCI 20-SOIC PDF资料下载
参数资料
| 型号： | MCP2210T-I/SO |
| 厂商： | Microchip Technology |
| 文件页数： | 82/82页 |
| 文件大小： | 0K |
| 描述： | IC CONVERTER USB-PCI 20-SOIC |
| 产品培训模块： | MCP2210 Evaluation Kit |
| 标准包装： | 1,600 |
| 应用： | 带 GPIO 的 USB 至 SPI 连接器 |
| 接口： | SPI，USB |
| 电源电压： | 3.3 V ~ 5.5 V |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页当前第82页
2011 Microchip Technology Inc.
DS22288A-page 9
MCP2210
2.0
MCP2210 FUNCTIONAL
DESCRIPTION
The MCP2210 uses NVRAM to store relevant chip
settings. These settings are loaded by the chip during
the power-up process and they are used for GP
designation and SPI transfers.
The NVRAM settings at power-up (or Reset) are
loaded into the RAM portion of the chip and they can be
altered through certain USB commands. This is very
useful since it allows dynamic reconfiguring of the GPs
or SPI transfer parameters. A practical example to
illustrate this mechanism is a system which uses at
least two SPI slave chips and the GPs in the MCP2210
for various GPIO purposes. The default SPI settings
might be ok for one of the SPI slave chips, but not for
the 2nd. At first, the PC application will make an SPI
transfer to the first chip, using the NVRAM copy of the
SPI settings. Then, by sending a certain USB
command, the SPI transfer settings residing in RAM
will be altered in order to fit the SPI transfer
requirements of the second chip.
Also, if the altered SPI transfer settings are needed to
be the default power-up (or Reset) settings for SPI, the
user can send a series of USB commands in order to
store the current (RAM) SPI settings into NVRAM. In
this way, these new settings will be the power-up
default SPI settings.
The NVRAM settings and EEPROM contents can be
protected by password access means, or they can be
permanently locked without any possible further
modification.
2.1
MCP2210 NVRAM Settings
The chip settings that can be stored in the NVRAM
area are as follows:
SPI transfer parameters:
- SPI bit rate
- SPI mode
- Idle Chip Select values
- Active Chip Select values
- SPI transfer configurable delays
- Number of bytes to read/write for the given
SPI transfer
GP designation:
-GPIO
- Chip Select
- Dedicated function
GPIO default direction (applies only to those GPs
designated as GPIOs)
GPIO default output value (applies only to those
GPs designated as output GPIOs)
Chip mode flags:
- Remote wake-up capability
- External Interrupt Pin mode (applies only
when GP6 is designated for this function)
- SPI bus release enable/disable – enable/
disable the release of the SPI bus when there
is no SPI transfer (useful when more than
one SPI master on the bus)
NVRAM Access mode:
- Full access (no protection – factory default)
- Password protection
- Permanently locked
Password (relevant when password protection
mechanism is active)
The specified settings are loaded at power-up or Reset
moments, and they can be altered through certain USB
commands.
When a NVRAM conditional access method is already
in place, such as password protection, the NVRAM
settings modification is permitted only when the user
has supplied the correct password for the chip. The
RAM settings can be altered even when a password
protection or permanent lock mechanism are in place.
This allows the user to communicate with various SPI
slave chips without knowing the password, but it will not
allow the modification of the power-up default settings
in NVRAM.
2.2
SPI Transfers
The MCP2210 device provides advanced SPI
communication features such as configurable delays
and multiple Chip Select support.
The configurable delays are related to certain aspects
of the SPI transfer:
The delay between the assertion of Chip Select(s)
and the first data byte (Figure 2-1)
FIGURE 2-1:
CHIP SELECT TO DATA
DELAY
TCS2DATA
CS
SCK
MOSI
MISO
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B4L-IX-F4 | CONVERTER MOD DC/DC 28V 75W |
| PIC12LF1501-I/MC | IC MCU 8BIT 1.75KB FLASH 8-DFN |
| VE-B4L-IX-F3 | CONVERTER MOD DC/DC 28V 75W |
| MS27508E18F66P | CONN RCPT 66POS BOX MNT W/PINS |
| MS27508E18B66P | CONN RCPT 66POS BOX MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2210T-I-SS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:USB-to-SPI Protocol Converter with GPIO (Master Mode) |
| MCP-22-I9-LL | 制造商:YAMAICHI 制造商全称:Yamaichi Electronics Co., Ltd. 功能描述:MatchCon |
| MCP-22-TI9-LL | 制造商:YAMAICHI 制造商全称:Yamaichi Electronics Co., Ltd. 功能描述:MatchCon |
| MCP-230-00005-00 | 制造商:SUPER MICRO COMPUTER, INC. 功能描述:SUPERMICRO TOP COVER SC823T - Bulk |
| MCP-230-00008-00 | 制造商:SUPER MICRO COMPUTER, INC. 功能描述:SUPERMICRO SC811 TOP COVER - Bulk |
发布紧急采购，3分钟左右您将得到回复。