- 您现在的位置：买卖IC网 > PDF目录67987 > MCP2515T-I/SO 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO18 PDF资料下载
参数资料
| 型号： | MCP2515T-I/SO |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO18 |
| 封装： | 7.50 MM, LEAD FREE, PLASTIC, SOIC-18 |
| 文件页数： | 8/88页 |
| 文件大小： | 1205K |
| 代理商： | MCP2515T-I/SO |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
MCP2515
DS21801F-page 16
2010 Microchip Technology Inc.
3.5
TXnRTS PINS
The TXnRTS pins are input pins that can be configured
as:
Request-to-send inputs, which provide an
alternative means of initiating the transmission of
a message from any of the transmit buffers
Standard digital inputs
Configuration and control of these pins is accomplished
using the TXRTSCTRL register (see Register 3-3). The
TXRTSCTRL register can only be modified when the
MCP2515 is in Configuration mode (see Section 10.0
“Modes of Operation”). If configured to operate as a
request-to-send pin, the pin is mapped into the
respective TXBnCTRL.TXREQ bit for the transmit
buffer. The TXREQ bit is latched by the falling edge of
the TXnRTS pin. The TXnRTS pins are designed to
allow them to be tied directly to the RXnBF pins to
automatically initiate a message transmission when the
RXnBF pin goes low.
The TXnRTS pins have internal pull-up resistors of
100 k
Ω (nominal).
3.6
Aborting Transmission
The MCU can request to abort a message in a specific
message
buffer
by
clearing
the
associated
TXBnCTRL.TXREQ bit.
In addition, all pending messages can be requested to
be aborted by setting the CANCTRL.ABAT bit. This bit
MUST be reset (typically after the TXREQ bits have
been verified to be cleared) to continue transmitting
messages. The TXBnCTRL.ABTF flag will only be set
if the abort was requested via the CANCTRL.ABAT bit.
Aborting a message by resetting the TXREQ bit does
NOT cause the ABTF bit to be set.
Note 1: Messages that were transmitting when
the abort was requested will continue to
transmit.
If
the
message
does
not
successfully complete transmission (i.e.,
lost arbitration or was interrupted by an
error frame), it will then be aborted.
2: When one-shot mode is enabled, if the
message is interrupted due to an error
frame
or
loss
of
arbitration,
the
TXBnCTRL.ABTF bit will set.
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2515-E/ST | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO20 |
| MCP2515T-E/ST | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO20 |
| MCP2515T-E/ML | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC20 |
| MCP2515-E/PG | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDIP18 |
| MCP2515-I/ST | 1 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2551 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed CAN Transceiver |
| MCP2551_07 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed CAN Transceiver |
| MCP2551_10 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed CAN Transceiver |
| MCP2551A-E/P | 功能描述:CAN 接口集成电路 Enhanced HI SPD CAN Transceiver RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
| MCP2551A-E/SN | 功能描述:CAN 接口集成电路 Enhanced HI SPD CAN Transceiver RoHS:否 制造商:Texas Instruments 类型:Transceivers 工作电源电压:5 V 电源电流: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。