- 您现在的位置：买卖IC网 > PDF目录10734 > MCP3201-CI/P (Microchip Technology)IC ADC 12BIT SINGLE CHAN 8DIP PDF资料下载
参数资料
| 型号： | MCP3201-CI/P |
| 厂商： | Microchip Technology |
| 文件页数： | 9/40页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SINGLE CHAN 8DIP |
| 标准包装： | 60 |
| 位数： | 12 |
| 采样率（每秒）： | 100k |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极 |
| 产品目录页面： | 672 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
1998-2011 Microchip Technology Inc.
DS21290F-page 17
MCP3201
4.0
DEVICE OPERATION
The MCP3201 A/D Converter employs a conventional
SAR architecture. With this architecture, a sample is
acquired on an internal sample/hold capacitor for
1.5 clock cycles starting on the first rising edge of the
serial clock after CS has been pulled low. Following this
sample time, the input switch of the converter opens
and the device uses the collected charge on the
internal sample and hold capacitor to produce a serial
12-bit digital output code. Conversion rates of 100 ksps
are possible on the MCP3201 device. See Section 6.2
for information
on minimum clock rates. Communication with the
device is done using a 3-wire SPI-compatible interface.
4.1
Analog Inputs
The MCP3201 device provides a single pseudo-differ-
ential input. The IN+ input can range from IN- to VREF
(VREF + IN-). The IN- input is limited to ±100 mV from
the VSS rail. The IN- input can be used to cancel small
signal common-mode noise which is present on both
the IN+ and IN- inputs.
For the A/D Converter to meet specification, the charge
holding capacitor (CSAMPLE) must be given enough
time to acquire a 12-bit accurate voltage level during
the 1.5 clock cycle sampling period. The analog input
model is shown in Figure 4-1.
In this diagram, it is shown that the source impedance
(RS) adds to the internal sampling switch (RSS)
impedance, directly affecting the time that is required to
charge the capacitor (CSAMPLE). Consequently, a
larger source impedance increases the offset, gain,
and integral linearity errors of the conversion.
Ideally, the impedance of the signal source should be
near zero. This is achievable with an operational
amplifier such as the MCP601, which has a closed loop
output impedance of tens of ohms. The adverse affects
of higher source impedances are shown in Figure 4-2.
If the voltage level of IN+ is equal to or less than IN-, the
resultant code will be 000h. If the voltage at IN+ is equal
to or greater than {[VREF + (IN-)] - 1 LSB}, then the
output code will be FFFh. If the voltage level at IN- is
more than 1 LSB below VSS, then the voltage level at
the IN+ input will have to go below VSS to see the 000h
output code. Conversely, if IN- is more than 1 LSB
above VSS, then the FFFh code will not be seen unless
the IN+ input level goes above VREF level.
4.2
Reference Input
The reference input (V
REF) determines the analog input
voltage range and the LSB size, as shown below.
EQUATION 4-1:
As the reference input is reduced, the LSB size is
reduced accordingly. The theoretical digital output code
produced by the A/D Converter is a function of the
analog input signal and the reference input as shown
below.
EQUATION 4-2:
When using an external voltage reference device, the
system designer
should
always
refer
to
the
manufacturer’s recommendations for circuit layout.
Any instability in the operation of the reference device
will have a direct effect on the operation of the
A/D Converter.
LSB Size
V
REF
4096
-------------
=
Digital Output Code
4096*V
IN
V
REF
-------------------------
=
Where:
VIN
=
Analog Input Voltage = V(IN+) - V(IN-)
VREF
=
Reference Voltage
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BWL-MY-B1 | CONVERTER MOD DC/DC 28V 50W |
| VE-J4Y-MW-F3 | CONVERTER MOD DC/DC 3.3V 66W |
| VI-BW3-MY-B1 | CONVERTER MOD DC/DC 24V 50W |
| LM239NG | IC COMP QUAD SGL SUPPLY 14DIP |
| MCP3201-CI/SN | IC ADC 12BIT SINGLE CHAN 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP3201-CISN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface |
| MCP3201-CIST | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface |
| MCP3201-I/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface |
| MCP3201-I/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface |
| MCP3201-I/SN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V 12-Bit A/D Converter with SPI Serial Interface |
发布紧急采购，3分钟左右您将得到回复。