- 您现在的位置：买卖IC网 > PDF目录17040 > MCP3901EV-MCU16 (Microchip Technology)BOARD EVAL FOR 2CH ADC MCP3901 PDF资料下载
参数资料
| 型号： | MCP3901EV-MCU16 |
| 厂商： | Microchip Technology |
| 文件页数： | 18/30页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR 2CH ADC MCP3901 |
| 产品培训模块： | MCP3901 Analog Front End |
| 视频文件： | MCP3901 ADC Evaluation Board for 16-bit MCUs |
| 标准包装： | 1 |
| ADC 的数量： | 2 |
| 位数： | 24 |
| 数据接口： | SPI? |
| 输入范围： | ±1 V |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | MCP3901 |
| 已供物品： | 板 |
| 产品目录页面： | 672 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
PCA2002
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 25 November 2011
25 of 30
NXP Semiconductors
PCA2002
32 kHz watch circuit with programmable output period and pulse width
14.3.2 Quality of solder joint
A flip-chip joint is considered to be a good joint when the entire solder land has been
wetted by the solder from the bump. The surface of the joint should be smooth and the
shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps
after reflow can occur during the reflow process in bumps with high ratio of bump diameter
to bump height, i.e. low bumps with large diameter. No failures have been found to be
related to these voids. Solder joint inspection after reflow can be done with X-ray to
monitor defects such as bridging, open circuits and voids.
14.3.3 Rework
In general, rework is not recommended. By rework we mean the process of removing the
chip from the substrate and replacing it with a new chip. If a chip is removed from the
substrate, most solder balls of the chip will be damaged. In that case it is recommended
not to re-use the chip again.
Device removal can be done when the substrate is heated until it is certain that all solder
joints are molten. The chip can then be carefully removed from the substrate without
damaging the tracks and solder lands on the substrate. Removing the device must be
done using plastic tweezers, because metal tweezers can damage the silicon. The
surface of the substrate should be carefully cleaned and all solder and flux residues
and/or underfill removed. When a new chip is placed on the substrate, use the flux
process instead of solder on the solder lands. Apply flux on the bumps at the chip side as
well as on the solder pads on the substrate. Place and align the new chip while viewing
with a microscope. To reflow the solder, use the solder profile shown in application note
AN10365 “Surface mount reflow soldering description”.
14.3.4 Cleaning
Cleaning can be done after reflow soldering.
相关PDF资料 |
PDF描述 |
|---|---|
| RBC12DRTH-S93 | CONN EDGECARD 24POS DIP .100 SLD |
| MLG1005SR18J | INDUCTOR MULTILAYER 180NH 0402 |
| RBC10DRES-S93 | CONN EDGECARD 20POS .100 EYELET |
| GEC18DRTS-S93 | CONN EDGECARD 36POS DIP .100 SLD |
| HBC06DRYN-S93 | CONN EDGECARD 12POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP3901-I/SS | 功能描述:开关变换器、稳压器与控制器 Dual Ch Enrgy Metr FrntEnd SPI Intrface RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCP3901T-I/SS | 功能描述:开关变换器、稳压器与控制器 Dual Ch Enrgy Metr FrntEnd SPI Intrface RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCP3903 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Six Channel Delta Sigma A/D Converter |
| MCP3903-E/SS | 功能描述:模数转换器 - ADC 6CH Energy Meter Fr End SPI Interface RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3903-E/SS | 制造商:Microchip Technology Inc 功能描述:; Leaded Process Compatible:Yes; Peak Re |
发布紧急采购，3分钟左右您将得到回复。