- 您现在的位置：买卖IC网 > PDF目录9328 > MCP4262T-503E/UN (Microchip Technology)IC RHEOSTAT 50K 2CH 10MSOP PDF资料下载
参数资料
| 型号： | MCP4262T-503E/UN |
| 厂商： | Microchip Technology |
| 文件页数： | 35/88页 |
| 文件大小： | 0K |
| 描述： | IC RHEOSTAT 50K 2CH 10MSOP |
| 标准包装： | 2,500 |
| 系列： | WiperLock™ |
| 接片： | 257 |
| 电阻（欧姆）： | 50k |
| 电路数： | 2 |
| 温度系数： | 标准值 150 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | MCP4262T-503-E/UN MCP4262T-503-E/UNTR MCP4262T-503-E/UNTR-ND MCP4262T-503E/UNTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
MCP414X/416X/424X/426X
DS22059B-page 40
2008 Microchip Technology Inc.
6.1
SDI, SDO, SCK, and CS Operation
The operation of the four SPI interface pins are
discussed in this section. These pins are:
SDI (Serial Data In)
SDO (Serial Data Out)
SCK (Serial Clock)
CS (Chip Select)
The serial interface works on either 8-bit or 16-bit
boundaries depending on the selected command. The
Chip Select (CS) pin frames the SPI commands.
6.1.1
SERIAL DATA IN (SDI)
The Serial Data In (SDI) signal is the data signal into
the device. The value on this pin is latched on the rising
edge of the SCK signal.
6.1.2
SERIAL DATA OUT (SDO)
The Serial Data Out (SDO) signal is the data signal out
of the device. The value on this pin is driven on the
falling edge of the SCK signal.
Once the CS pin is forced to the active level (VIL or
VIHH), the SDO pin will be driven. The state of the SDO
pin is determined by the serial bit’s position in the
command, the command selected, and if there is a
command error state (CMDERR).
6.1.3
SDI/SDO
For device packages that do not have enough pins for
both an SDI and SDO pin, the SDI and SDO
functionality is multiplexed onto a single I/O pin called
SDI/SDO.
The SDO will only be driven for the command error bit
(CMDERR) and during the data bits of a read command
(after the memory address and command has been
received).
6.1.3.1
SDI/SDO Operation
Figure 6-2 shows a block diagram of the SDI/SDO pin.
The SDI signal has an internal “smart” pull-up. The
value of this pull-up determines the frequency that data
can be read from the device. An external pull-up can be
added to the SDI/SDO pin to improve the rise time and
therefore improve the frequency that data can be read.
Data written on the SDI/SDO pin can be at the
maximum SPI frequency.
On the falling edge of the SCK pin during the C0 bit
(see Figure 7-1), the SDI/SDO pin will start outputting
the SDO value. The SDO signal overrides the control of
the smart pull-up, such that whenever the SDI/SDO pin
is outputting data, the smart pull-up is enabled.
The SDI/SDO pin will change from an input (SDI) to an
output (SDO) after the state machine has received the
Address and Command bits of the Command Byte. If
the command is a Read command, then the SDI/SDO
pin will remain an output for the remainder of the
command. For any other command, the SDI/SDO pin
returns to an input.
FIGURE 6-2:
Serial I/O Mux Block
Diagram.
Note:
MCP41X1 Devices Only .
Note:
To support the High voltage requirement of
the SDI function, the SDO function is an
open-drain output.
Note:
Care must be take to ensure that a Drive
conflict does not exist between the Host
Controllers SDO pin (or software SDI/SDO
pin) and the MCP41x1 SDI/SDO pin (see
SDI/SDO
SDI
SDO
Control
“smart” pull-up
Open
Drain
Logic
相关PDF资料 |
PDF描述 |
|---|---|
| M83723/83W2219N | CONN RCPT 19POS WALL MT W/PINS |
| MCP4261T-503E/SL | IC DGTL POT 50K 2CH 14SOIC |
| MCP4261T-503E/ST | IC DGTL POT 50K 2CH 14TSSOP |
| VI-2NX-MY-F2 | CONVERTER MOD DC/DC 5.2V 50W |
| VE-BNK-IU-F4 | CONVERTER MOD DC/DC 40V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP42XXDM-PTPLS | 功能描述:子卡和OEM板 MCP42XX PICTail Plus Daughter Board RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MCP42XXEV | 功能描述:数字电位计开发工具 MCP42XX Eval Board RoHS:否 制造商:Arduino 产品:TinkerKit Rotary Potentiometers 工具用于评估:TinkerKit 电阻:4.7 kOhms 工作电源电压:0 V to 5 V |
| MCP431550R | 制造商:Eaton Corporation 功能描述:TYPE MCP MOTOR CIRCUIT PROTECTOR 150A FOR SIZE 4 STARTER |
| MCP4331-103E/ML | 功能描述:数字电位计 IC 10k SPI 7-bit Quad Chl, QFN20 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MCP4331-103E/ST | 功能描述:数字电位计 IC 10k SPI 7-bit Quad Chl, TSSOP20 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。