- 您现在的位置：买卖IC网 > PDF目录16593 > MCZ33742EGR2 (Freescale Semiconductor)IC SYSTEM BASIS CHIP CAN 28-SOIC PDF资料下载
参数资料
| 型号： | MCZ33742EGR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 20/71页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASIS CHIP CAN 28-SOIC |
| 标准包装： | 1,000 |
| 应用： | 自动 |
| 电流 - 电源： | 42mA |
| 电源电压： | 5.5 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
OPERATIONAL MODES
INTRODUCTION
The 33742 has four modes of operation, all controllable via the SPI. The modes are Standby, Normal, Stop, and Sleep. An
additional temporary mode called Normal Request mode is automatically accessed by the device after reset or wake-up from
Stop mode. A Reset mode is also implemented. Special modes and configurations are possible for debug and program
microcontroller flash memory.
Table , page 28, offers a summary of the functional modes.
STANDBY MODE
In Standby mode only the VDD regulator is ON. The V2 regulator is turned OFF by disabling the V2CTRL pin. Other functions
available are the L0:L3 inputs read through via the SPI and HS output activation.
The CAN interface is not able to send messages. If a CAN message is received, the CANWU bit is set. The watchdog timer
is running.
NORMAL MODE
In Normal mode, both the VDD and V2 regulators are in the ON state. All functions are available in this operating mode
(watchdog, wake-up input reading through SPI, HS activation, and CAN communication). The watchdog timer is running and
must be periodically cleared through SPI.
STOP MODE
The V2 regulator is turned OFF by disabling the V2CTRL pin. The VDD regulator is activated in a special low power mode
supplying only a few mA of current. This maintains “keep alive” power for the application’s MCU while the MCU is in a power-
saving state (i.e., a MCU’s version of Stop or Wait). In the Stop mode, the supply current available from VSUP pin is very low.
Both parts (the SBC or the MCU) can be awakened from either the 33742 side (for example, cyclic sense, forced wake-up,
CAN message, wake-up inputs, and over-current on VDD) or from the MCU side (key wake-up, etc.).
Stop mode is always selected via SPI. In Stop mode, the watchdog software may be either running or not running depending
upon selection by SPI (Reset Control Register [RCR], bit WDSTOP). To clear a running watchdog timer, the SBC must be
awakened using the CS pin (SPI wake-up). In Stop mode, wake-up is identical to that in Sleep mode, with the addition of CS and
SLEEP MODE
In Sleep mode, the VDD and V2 regulators are OFF. Current consumption from the VSUP pin is cut. In Sleep mode, the SBC
can be awakened by sensing individual level individual level changes in the L0:L3 inputs, by cyclic checking of the L0:L3 inputs,
by the forced wake-up timer, or from the CAN physical interface upon receiving a CAN message. When a wake-up occurs, the
SBC goes first into the Reset mode before entering Normal Request mode.
RESET MODE
In the Reset mode, the RST pin is LOW and a timer runs for tRSTDUR time. After tRSTDUR has elapsed, the 33742 enters the
Normal Request operating mode. The Reset mode is entered if a reset condition occurs (VDD LOW, watchdog time-out, or
watchdog trigger in a closed window).
NORMAL REQUEST MODE
The Normal Request mode is a temporary operating mode automatically entered by the SBC after the Reset mode or after the
33742 wakes up from the Stop mode.
After a wake-up from the Sleep mode or after a device power-up, the SBC enters the Reset mode prior to entering the Normal
Request mode. After a wake-up from the Stop mode, the 33742 enters the Normal Request mode directly.
In Normal Request mode, the VDD regulator is ON, the V2 regulator is OFF, and the RST pin is HIGH. As soon as the SBC
enters the Normal Request mode, an internal 350ms timer is started (parameter tNRTOUT). During this time, the application’s MCU
must address the 33742 via SPI and configure the TIM1 sub register to select the watchdog period. This is required of the SBC
to stop the 350 ms watchdog timer and enter the Normal or Standby mode and to set the watchdog timer configuration.
相关PDF资料 |
PDF描述 |
|---|---|
| ECM30DCAN | CONN EDGECARD 60POS R/A .156 SLD |
| EVAL-ADCMP561BRQZ | BOARD EVALUATION ADCMP561BRQZ |
| VI-BNB-EW | CONVERTER MOD DC/DC 95V 100W |
| A3AAB-2036M | IDC CABLE- ASC20B/AE20M/ASC20B |
| VI-BN2-EX | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33742SEG | 功能描述:网络控制器与处理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33742SEGR2 | 功能描述:网络控制器与处理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33780EG | 功能描述:多路器开关 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MCZ33780EG | 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC |
| MCZ33780EGR2 | 功能描述:多路器开关 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。