参数资料
型号: MCZ33742EGR2
厂商: Freescale Semiconductor
文件页数: 31/71页
文件大小: 0K
描述: IC SYSTEM BASIS CHIP CAN 28-SOIC
标准包装: 1,000
应用: 自动
电流 - 电源: 42mA
电源电压: 5.5 V ~ 18 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 28-SOIC(0.295",7.50mm 宽)
供应商设备封装: 28-SOIC W
包装: 带卷 (TR)
Analog Integrated Circuit Device Data
Freescale Semiconductor
37
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
CAN PHYSICAL INTERFACE
The SBC features a high-speed CAN physical interface for bus communication from 60kbps up to 1.0Mbps. Figure 19 is a
simplified block diagram of the CAN interface of the 33742.
Figure 19. Simplified Block Diagram of CAN Interface
CAN INTERFACE SUPPLY
The supply voltage for the CAN transceiver is the V2 pin. The CAN interface also has a supply path from the external supply
line through the VSUP pin. This path is used in CAN Sleep mode to allow wake-up detection.
During CAN communication (transmission and reception), the CAN interface current is sourced from the V2 pin. During CAN
low power mode, the current is sourced from the VSUP pin.
MAIN OPERATION MODES DESCRIPTION
The CAN interface of the SBC has two main operating modes: TXRX and Sleep mode. The modes are controlled by the CAN
SPI Register. In the TXRX mode, which is used for communication, four different slew rates are available for the user. In the
Sleep mode, the user has the option of enabling or disabling the remote CAN wake-up capability.
CAN DRIVER OPERATION IN TXRX MODE
When the CAN interface is in TXRX mode, the driver has two states: recessive or dominant. The driver state is controlled by
the TXD pin. The bus state is reported through the RXD pin.
When TXD is HIGH, the driver is set in recessive state, and CANH and CANL lines are biased to the voltage set at V2 divided
by 2, or approximately 2.5 V.
When TXD is LOW, the bus is set into dominant state: CANL and CANH drivers are active. CANL is pulled to ground, and
CANH is pulled HIGH toward 5.0 V (voltage at V2).
The RXD pin reports the bus state: CANH minus CANL voltage is compared versus an internal threshold (a few hundred
millivolts). If CANH minus CANL is below the threshold, the bus is recessive and RXD is set HIGH. If CANH minus CANL is above
the threshold, the bus is dominant and RXD is set LOW. This is illustrated in Figure 19.
V2
Bus Termination (60
)
CANH Line
CANL Line
TXD
RXD
Differential
Receiver
Driver
2.5 V
Wake-up
Receiver
Pattern
Recognition
Internal
VSUP
Wake-up
Signal
CANH
CANL
SPI Control
V2
QH
QL
33742
相关PDF资料
PDF描述
ECM30DCAN CONN EDGECARD 60POS R/A .156 SLD
EVAL-ADCMP561BRQZ BOARD EVALUATION ADCMP561BRQZ
VI-BNB-EW CONVERTER MOD DC/DC 95V 100W
A3AAB-2036M IDC CABLE- ASC20B/AE20M/ASC20B
VI-BN2-EX CONVERTER MOD DC/DC 15V 75W
相关代理商/技术参数
参数描述
MCZ33742SEG 功能描述:网络控制器与处理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MCZ33742SEGR2 功能描述:网络控制器与处理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
MCZ33780EG 功能描述:多路器开关 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻(最大值):7 Ohms 开启时间(最大值): 关闭时间(最大值): 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16
MCZ33780EG 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC
MCZ33780EGR2 功能描述:多路器开关 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻(最大值):7 Ohms 开启时间(最大值): 关闭时间(最大值): 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16