- 您现在的位置：买卖IC网 > PDF目录1954 > MCZ33781EKR2 (Freescale Semiconductor)IC MASTER DSI 2.02 DIFF 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33781EKR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 13/44页 |
| 文件大小： | 0K |
| 描述： | IC MASTER DSI 2.02 DIFF 32-SOIC |
| 标准包装： | 1,000 |
| 应用： | 车载系统 |
| 接口： | SPI |
| 电源电压： | 4.75 V ~ 5.25 V |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
33781
FUNCTIONAL DESCRIPTIONS
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
PSEUDO BUS SWITCHES
Pseudo Bus Switches are provided on the Channel 0 bus.
They allow one channel to communicate via two external bus
wire sets (D0H/D0L and DPH/DPL). There is a pseudo bus
switch on both the bus high and bus low driver. Upon device
reset the bus switches are open. This allows the master to
initialize devices on D0H/D0L. After all of these slaves are
initialized, the pseudo bus switches can be closed, allowing
the devices on DPH/DPL to be initialized.
The Pseudo Bus Switches can only be commanded closed
by the BSWH and BSWL bits in the D0EN register. These bits
can also open the switch at any time.
The Pseudo Bus Switches have independent thermal
shutdown protection. Once the thermal shutdown point is
reached, the bus switch is opened (becoming high-
impedance) and the BSWH and/or BSWL bit is cleared in the
channel 0 DEN register. If this occurs, the Pseudo Bus
Switches can only be closed again by setting the BSWH and/
or BSWL bit to a 1 with a write command to the channel 0
DEN register.
SPREAD SPECTRUM
The dominant source of radiated electromagnetic
interference (EMI) from the DBUS bus is due to the regular
periodic frequency of the data bits. At a steady bit rate, the
time period for each bit is the same, which results in a steady
fundamental frequency plus harmonics. This results in
undesired signals appearing at multiples of the frequency
that can be strong enough to interfere with a desired signal.
A significant decrease in radiated EMI can be achieved by
randomly changing the duration of each bit. This can
significantly reduce the amplitude by having the signal spend
a much smaller percentage of time at any specific frequency.
The signal strength of the fundamental and harmonics are
reduced directly by the percentage of time it spends on a
specific frequency.
A circuit to do this is included in this IC, and can perform
the spreading of the signal independently for each channel,
while generating the bit clock timing for the channel. This is
done in the Spread Spectrum (SS) Block Diagram shown in
To implement the channel bit clock a common 64MHz
clock is created from the on board 4MHz oscillator using a
digital PLL. Multiples of this clock period (15.625 nsec) are
used to select the minimum channel bit time. The Spread
Table 7. Receiver Decision Logic
Bus Pin
Conditions
Receiver
High 6 ± 1
mA
Receiver
Low 6 ± 1
mA
Receiver
Sum 12 ±
6mA
High and
Low XOR
(bit/bit)
High and
Sum XOR
(bit/bit)
Low and
Sum XOR
(bit/bit)
ER Bit
SPI0
DnRnxData
SPI1
DnRnxData
Normal
CRC Ok
H*L Ok
N/A
0
Receiver
High
Receiver
Low
H*L Not OK
1
Receiver
High
Receiver
Low
Out of Spec
CRC Ok
Bad CRC
H*L Ok
N/A
0
Receiver
High
Receiver
Low
H*L Not OK
1
Receiver
High
Receiver
Low
Fault
CRC Ok
Bad CRC
CRC Ok
N/A
H*S Ok
N/A
0
Receiver
High
Receiver
Sum1
H*S Not OK
1
Receiver
High
Receiver
Low
Fault L
CRC Ok
Bad CRC
N/A
1
Receiver
High
Receiver
Low
Fault
Bad CRC
CRC OK
N/A
L*S Ok
0
Receiver
Sum0
Receiver
Low
L*S Not OK
1
Receiver
High
Receiver
Low
Fault H
Bad CRC
CRC Ok
Bad CRC
N/A
1
Receiver
High
Receiver
Low
Common
Mode Noise
Bad CRC
CRC Ok
N/A
0
Receiver
Sum0
Receiver
Sum1
Fault
Bad CRC
N/A
1
Receiver
High
Receiver
Low
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33784EFR2 | IC SENSOR DBUS DSI 2.02 16-SOIC |
| MCZ33793EF | IC DSI SLAVE REMOTE SENS 16-SOIC |
| MCZ33797EKR2 | IC SQUIB DRIVER 2CHAN 32-SOIC |
| MCZ33884EG | IC MULTIPLE CONTACT MON 24-SOIC |
| MCZ33905BD3EK | IC SBC CAN HS 3.3V 54SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33784EF | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33784EF/R2- | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:DSI 2.02 Sensor Interface |
| MCZ33784EFR2 | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33789AE | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33789AE/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Airbag System Basis Chip (SBC) with Power Supply and PSI5 Sensor Interface |
发布紧急采购，3分钟左右您将得到回复。