- 您现在的位置：买卖IC网 > PDF目录1954 > MCZ33781EKR2 (Freescale Semiconductor)IC MASTER DSI 2.02 DIFF 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33781EKR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 21/44页 |
| 文件大小： | 0K |
| 描述： | IC MASTER DSI 2.02 DIFF 32-SOIC |
| 标准包装： | 1,000 |
| 应用： | 车载系统 |
| 接口： | SPI |
| 电源电压： | 4.75 V ~ 5.25 V |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Analog Integrated Circuit Device Data
28
Freescale Semiconductor
33781
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
SPI1 REGISTERS
An eight position circular buffer made up of 16-bit words.
Reads of these registers occur in a round robin (sequential
order with wrap around at the end) fashion. If a buffer does
not contain any data it is skipped during the round robin
sequence. More information on this buffer can be found in the
section SPI1 Communications.
RST
Asserting this pin low will cause the part to reset, forcing
registers to a known state and resetting the SPI0 and SPI1
buffer pointers. All bus activity will be halted and not allowed
to restart, and no SPI activity will be recognized until the RST
goes to a logic high level.
ADDRESSED TX BUFFER
The Addressed TX Buffer is a cyclic register set that allows
up to four transmit data packets to be stored for future
transmission on the DBUS. This is done to prevent the
overwrite of transmit data if the transmission of the previous
data has not been completed. Each buffer is a 2-byte set that
contains the high byte and low byte of a DBUS command.
The transmit buffer queue looks for the lowest register
number in the channel with data to be sent, and sends it over
the DBUS. It then checks the next sequential buffer - if there
is data to be sent it will send it. If not, that buffer will be
skipped and the next buffer sent if it contains data. If no other
buffers have data ready to be sent, the queue moves back to
the top of the buffer and continues checking until data is
available.
ADDRESSED RX BUFFER
The Addressed RX Buffer is a cyclic register set that
allows up to four responses to be stored without being
transferred to the MCU via the SPI. This is done so that data
will not be lost, even if the MCU takes time to read the
response data. Each buffer is a 3-byte set that contains the
data high byte, data low byte, and status word of a DBUS
response.
The received data from DBUS transactions is stored in the
same receive buffer number as the transmit buffer for that
transaction.
BUS DRIVER/RECEIVER LOGIC
This block controls the physical layer drivers and receive
data from the physical layer receivers. The physical layer
converts the 0V to 5.0V low power logic signals to the higher
voltage and drive levels required for the bus. It also converts
the low current (0mA to 11mA typical) loading of the response
signal from the slave to logic voltage levels, to allow the
response from the slaves to be received.
Each channel contains a CRC generator, that adds a
series of bits to each of the transmitted data words sent out
on the DBUS. The CRC bits are created from the data pattern
and are used by the slave devices to determine if one or more
of the data bits sent was in error. The detailed operation and
control of this function is covered in the section entitled CRC
This block also checks the CRC bits that have been added
to the end of the response by the slave device. For a given
pattern of received data, a new CRC is generated and
compared to the CRC bits received. This is performed on the
received data from the bus high side, bus low side and bus
sum circuits in the bus receiver. The results of these checks,
determine if the data are valid, and whether or not the error
bit is set as shown in Table 9. This bit is read back using the
SPI during the same SPI transaction that reads the response,
in order to keep them associated with each other. The CRC
bits are removed by the IC and not seen by the MCU, when
reading the data registers. Operation of the CRC Check is
covered in the section entitled CRC GENERATION /
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33784EFR2 | IC SENSOR DBUS DSI 2.02 16-SOIC |
| MCZ33793EF | IC DSI SLAVE REMOTE SENS 16-SOIC |
| MCZ33797EKR2 | IC SQUIB DRIVER 2CHAN 32-SOIC |
| MCZ33884EG | IC MULTIPLE CONTACT MON 24-SOIC |
| MCZ33905BD3EK | IC SBC CAN HS 3.3V 54SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33784EF | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33784EF/R2- | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:DSI 2.02 Sensor Interface |
| MCZ33784EFR2 | 功能描述:加速计 - 板上安装 DBUS2 SENSOR INTERFACE RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MCZ33789AE | 功能描述:网络控制器与处理器 IC Airbag ASSP RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33789AE/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Airbag System Basis Chip (SBC) with Power Supply and PSI5 Sensor Interface |
发布紧急采购，3分钟左右您将得到回复。