- 您现在的位置：买卖IC网 > PDF目录11649 > MCZ33793EFR2 (Freescale Semiconductor)IC DSI SLAVE FOR R-SENSE 16-SOIC PDF资料下载
参数资料
| 型号： | MCZ33793EFR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 14/27页 |
| 文件大小： | 0K |
| 描述： | IC DSI SLAVE FOR R-SENSE 16-SOIC |
| 标准包装： | 1 |
| 类型： | 传感器接口 |
| 输入类型： | 逻辑 |
| 输出类型： | 逻辑 |
| 接口： | 并联 |
| 电流 - 电源： | 250mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 标准包装 |
| 产品目录页面： | 808 (CN2011-ZH PDF) |
| 其它名称： | MCZ33793EFR2DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
33793
FUNCTIONAL DEVICE OPERATION
DSI COMMANDS AND RESPONSES
REVERSE INITIALIZATION RESPONSE
This response message is sent during the next message
following a valid Reverse Initialization command to the
addressed device. The response is shown in Table 28. Since
this is a long-word only command, the short-word response is
invalid. No response is generated if the command address
field was $0.
Table 27. Reverse Initialization Command Format
Data
Address
Command
CRC
NV
BS
G1
G0
PA3
PA2
PA1
PA0
A3
A2
A1
A0
1
X3
X2
X1
X0
Legend
A[3:0] = Address bits. These bits are the slave address. For
programmable devices these bits are all set to zero. For pre-
programmed devices these bits contain the pre-programmed
address and must match the PA[3:0] bits.
G[1:0] = Group bits. These bits are the group number for the slave.
These bits are not used by this device and should be set to “0”.
PA[3:0] = Program Address bits. These bits are the address that is
to be stored into the slave’s address register.
NV = Nonvolatile Memory Write. When set to a one, this bit allows a
subsequent NVM command to store a nonvolatile address. When set to a
zero, NVM programming is disallowed. Once a permanent address has
been stored in the device, setting the NV bit to a one has no effect.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
master.
Table 28. Reverse Initialization Response Format
High Byte
Low Byte
CRC
A3
A2
A1
A0
0
BF
NV
BS
G1
G0
PA3 PA2 PA1 PA0 X3
X2
X1
X0
Legend
A[3:0] = Address bits.The slave address.
BF = Bus Fault. BUSIN short to battery detected.
BS = Controls closing of the Bus Switch (1=close).
G[1:0] = Group bits. Not used on this part, will be set to “0”. The
group number programmed into the slave.
NV = Nonvolatile Memory Write. The value of the NV bit in the slave.
PA[3:0] = Bus Address to set the device to.
X[3:0] = Cyclic Redundancy Check (CRC). The CRC as calculated by the
slave.
相关PDF资料 |
PDF描述 |
|---|---|
| CS4121EDWFR20G | IC TACH/SPEEDO DRIVER 20-SOIC |
| CS4121EDWFR20 | IC TACH/SPEEDO DRIVER 20-SOIC |
| CS4121EDWF20G | IC TACH/SPEEDO DRIVER 20-SOIC |
| CS4121EDWF20 | IC TACH/SPEEDO DRIVER 20-SOIC |
| 415484-1 | CONN SMB PLUG RG179 R/A CRIMP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33797EK | 功能描述:功率驱动器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MCZ33797EKR2 | 功能描述:功率驱动器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MCZ33800EK | 功能描述:马达/运动/点火控制器和驱动器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33800EKR2 | 功能描述:马达/运动/点火控制器和驱动器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
发布紧急采购，3分钟左右您将得到回复。