参数资料
型号: MCZ33793EFR2
厂商: Freescale Semiconductor
文件页数: 4/27页
文件大小: 0K
描述: IC DSI SLAVE FOR R-SENSE 16-SOIC
标准包装: 1
类型: 传感器接口
输入类型: 逻辑
输出类型: 逻辑
接口: 并联
电流 - 电源: 250mA
安装类型: 表面贴装
封装/外壳: 16-SOIC(0.154",3.90mm 宽)
供应商设备封装: 16-SOIC N
包装: 标准包装
产品目录页面: 808 (CN2011-ZH PDF)
其它名称: MCZ33793EFR2DKR
Analog Integrated Circuit Device Data
12
Freescale Semiconductor
33793
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
Read the general purpose I/O logic values and respond
to request for these values.
Generating a cycle redundancy check (CRC) for the
received data and transmitted data in conformance with
the DSI Bus Standard.
Additionally, the control logic performs error checking on the
received data. If errors are found, no action is taken and no
response is made. Errors include:
CRC received doesn’t match CRC of received data.
Number of received bits is not 12 or 20.
CLOCK
The clock is a low-stability type with the capacitor integrated
onto the die. The signaling system and all internal operations
are such that no external precision timing device is needed in
the normal operation of this device.
BUS SWITCH (BUSSW)
The bus switch passes signaling and power to all subsequent
devices on the bus. It can block a voltage of either polarity up
to the highest idle state level between BUSIN and BUSOUT.
LOGICOUT
LOGICOUT is a logic level output with enhanced high-side
drive capability.
ADDRESSING
The 33793 IC supports both runtime programmable and pre-
programmed addressing as defined in the DSI Specification.
Runtime programmable addressing uses the daisy chain bus
connection. Pre-programmed devices may either be
connected in daisy chain or in parallel on the bus wires.
Programmable address devices all power up with a device
address of $0 in their address register and their bus switches
open. In the daisy chain, if the first device receives the
initialization command device on BUSIN, it will accept the
address in the command and close its switch at the end of the
command. The next device in the chain will now be able to
receive the initialization command on its BUSIN and will
accept the next address. This proceeds down the chain until
the last device is addressed. The devices can also be
initialized by the reverse initialization command if the signal is
applied to BUSOUT.
Pre-programmed devices power up with their pre-
programmed address in its address register. It will ignore all
Initialization commands unless the address in the command
matches its pre-programmed address. In this event the
device stores the other information contained in the
Initialization command.
相关PDF资料
PDF描述
CS4121EDWFR20G IC TACH/SPEEDO DRIVER 20-SOIC
CS4121EDWFR20 IC TACH/SPEEDO DRIVER 20-SOIC
CS4121EDWF20G IC TACH/SPEEDO DRIVER 20-SOIC
CS4121EDWF20 IC TACH/SPEEDO DRIVER 20-SOIC
415484-1 CONN SMB PLUG RG179 R/A CRIMP
相关代理商/技术参数
参数描述
MCZ33797EK 功能描述:功率驱动器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MCZ33797EKR2 功能描述:功率驱动器IC FOUR CHANNEL SQUIB DR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MCZ33800EK 功能描述:马达/运动/点火控制器和驱动器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33800EKR2 功能描述:马达/运动/点火控制器和驱动器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33800R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit