- 您现在的位置：买卖IC网 > PDF目录11718 > MCZ33884EGR2 (Freescale Semiconductor)IC MULTIPLE CONTACT MON 24-SOIC PDF资料下载
参数资料
| 型号： | MCZ33884EGR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 7/21页 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLE CONTACT MON 24-SOIC |
| 标准包装： | 1,000 |
| 系列： | * |
| 应用： | * |
| 接口： | * |
| 电源电压： | * |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
33884
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
TRI-STATE COMMAND
This command places an external switch into a Tri-State
condition, essentially disconnecting the wetting current (if the
switch is metallic) and the sustain current. The internal input-
threshold comparator is still internally connected to its
external pin. This command does not change the mode of
operation
CP[4:1] – CONFIGURE PROGRAMMABLE SWITCH
Configure the programmable inputs SP[4:1] to detect
either an external switch-to-ground (internal current source)
or an external switch-to-battery (internal current sink).
Note: This configuration may be entered in any of the three
valid Operating Modes (see MOD[2:1]) within the Run
command.
(e.g., a Tri-State command received while in the Polling
mode leaves the part in that mode).
Note: The Tri-State register clears all bits to logic [0] (all
inputs in Tri-State) in response to a hardware reset; all inputs
also remain in Tri-State after existing the Sleep mode.
METALLIC COMMAND
This command enables the pulsed wetting current for an
external metallic switch and disables it for an external non-
metallic switch. This command does not change the mode of
operation (e.g., a Metallic command received while in Polling
mode leaves the part in that mode). Note that the Run
register values are unknown after exiting the Sleep mode.
Table 11. Programmable Switch Bit Definition
CPx
External Switch to:
0
Ground
1
Battery
Table 12. Tri-State Command
MSB
LSB
Command
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Tri-State
0
1
TG6
TG5
TG4
TG3
TG2
TG1
TP4
TP3
TP2
TP1
TB2
TB1
Reset Values:
Run Register
—
0
TG[6:1] = Tri-state switch-to-ground
TB[2:1] = Tri-state switch-to-battery
TP[4:1] = Tri-state programmable switch
Table 13. Programmable Switch Bit Definition
TGx, TBx, TPx
Input Configured to:
0
Input Disabled (Default)
1
Input Enabled
Table 14. Metallic Command
MSB
LSB
Command
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Metallic
0
1
0
1
MG6
MG5
MG4
MG3
MG2
MG1
MP4
MP3
MP2
MP1
MB2
MB1
Reset Values:
Run Register
—
U
U = Unknown value coming out of Sleep mode. It must be configured with Run command.
MG[6:1] = Metallic switch-to-ground
MB[2:1] = Metallic switch-to-battery
MP[4:1] = Metallic programmable switch
Table 15. Metallic Switch Bit Definition
MGx, MBx, MPx
Accept Switch Type:
0
Non-Metallic
1
Metallic (Enable Wetting Current Pulse)
相关PDF资料 |
PDF描述 |
|---|---|
| V110B8H150BL3 | CONVERTER MOD DC/DC 8V 150W |
| MS27484T18A35SN | CONN PLUG 66POS STRAIGHT W/SCKT |
| MCZ33990EFR2 | IC TRANSCEIVER J-1850 BUS 8-SOIC |
| V110B8H150BG | CONVERTER MOD DC/DC 8V 150W |
| D38999/26JC8HN | CONN PLUG 8POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33887EK | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33887EKR2 | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33887EKR2DH | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:5.0 A H-Bridge with Load Current Feedback |
| MCZ33889BEG | 功能描述:网络控制器与处理器 IC SBC-LITE-LS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33889BEG | 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER |
发布紧急采购，3分钟左右您将得到回复。